Kodak Printe manual Installing additional memory, Acceptable Simm sizes, Simm installation

Page 31

Installing additional memory

A

The VinylJet 36 ships with 32 MB of DRAM, upgradable to a maximum of 128 MB, 64 MB per socket. Additional memory helps to free the host computer more quickly.

Acceptable SIMM sizes

Printer memory may be upgraded by installing 72-pin 60 nanosecond (or faster) SIMMs that are either 32 or 36 bits wide. (The printer does not use parity bits.) The SIMMs must not exceed a height of 2 inches (5 cm) and must conform to JEDEC Std. 21-C, release 4.

The printer will accept 4 MB, 8 MB, 16 MB, 32 MB or 64 MB SIMMs. Recommended SIMMs are ENCAD P/N 210610 (32MB SIMM).

SIMM installation

The SIMMs are located on the MPCB inside the right cover. The MPCB comes with one SIMM slot empty and a 32 MB RAM SIMM installed on the board. The following procedures describe how to remove the right cover, remove any currently installed SIMM(s), install new SIMM(s) and replace the cover. You will need a #2 Phillips screw- driver to complete the procedures.

!ALWAYS UNPLUG THE POWER CORD BEFORE BEGINNING.

!To avoid static damage to the printer, never touch the circuit board or its components without first touching the bright metal portions of the printer. Static damage is more likely when the relative humidity is low. If possible, wear a grounding strap when touching the circuit board.

To remove the right cover

1Disconnect the power and the interface cables.

2Remove the printer's top cover.

3Remove the three screws under the right side of the printer which attach the right side cover and the two screws which attach the cover to the right plate.

4Slide back the pin that holds the right cover to the rear cover.

5Move the right cover, being careful to clear the parallel port on the back of the unit.

6Carefully disconnect the ribbon cable from the connector on the PC board and the other two cables that go to the cover.

Image 31
Contents Revision History Text P/NWarranty Claims VDE statement FCC Statement U.S.AGeneral operating safety Material safety data sheetIndustry Canada For your safety Other reference materials Manual conventionsContents Appendix B Menu tree Appendix a Installing additional memoryAppendix C Technical information Appendix D Error messages Appendix E TroubleshootingPrinter setup Obtaining quality results PrintingUse the right inks and media Choose the right media Caring for your ink and cartridgesCaring for your media Use the right software Choose the correct printing modeImportant notes about image size vs. dpi Returning to the default settingsPrinting the settings Printer optionsTo choose the color mode Color modeChoosing quality mode options To enter a media length value To choose print qualityChoosing feed media options Media counterTo display the current value To reset the media counterAuto-load delay To set auto-load delayAuto-Wipe Defining user setupSave media To turn off Save MediaTo choose a language To save user setupTo use a previously saved user setting Choosing a languageChoosing ink options To set LCD contrastTo set ink reduction To set dry EOP To set the ink preheat timeUser Settings Default Other Options Printer default settingsPrinting To print a file using the Windows driverEnd of Print function Printing vector data Printing modesTo choose a palette type Accessing HP-GL/2 featuresTo access HP-GL/2 features Palette selectRotation ControlTo set control To rotate the image ReprintsTo make multiple prints Nesting Nest time To enable nestingTo define nesting wait time Ink limit To enable the ink limitTo remove the right cover Installing additional memorySimm installation Acceptable Simm sizesTo remove the SIMMs To install the new SimmMain menu at a glance Menu treeFeed media menu Main menuSetup menu at a glance Bold indicates the default Utility menu at a glance Bold indicates the default Print Mode Setup menuHP-GL/2 Menu Ink Option Menu Utility menu Serial Comm Menu Bold indicates the defaultPrime menu Service Menu Bold indicates the default Media Roll Parameters Technical informationTechnical information C-2 Cartridge errors Error messagesMemory Errors Troubleshooting quick list TroubleshootingEIsolating problems Printer health File will not print Printer front view Ink cartridges do not fire properly Firmware Download Procedure Upgrade/Printer Refresh Overall print quality is poor Calibrate cartridges Data Transfer No output when printing from Unix Application Software Difficulty generating prints ranging from a to D size Calling for Help Customer Technical Support