Xantrex Technology C40, C35, C60 owner manual Features and Options Specifications

Page 91

Features and Options Specifications

Table A-1Electrical Specifications

Model	C35	C40

C60

Load Control Settings:

System Voltage:

Low Voltage

Reconnect

Low Voltage

Disconnect

12 Volt System:

LVR 12.0 to 14.0 Vdc

LVD 10.5 to 12.5 Vdc

24 Volt System:

LVR 24.0 to 28.0 Vdc

LVD 21.0 to 25.0 Vdc

48 Volt System:

LVR 48.0 to 56.0 Vdc

LVD 42.0 to 50.0 Vdc

Features and Options Specifications

The following lists the features and options specifications for the C-Series controllers Models C35, C40, and C60.

Table A-2Features and Options Specifications

Model	C35	C40		C60

Standard Features

Status Indicator	Multi color LED indicates the operating/battery voltage status.

Low Voltage Disconnect	User selectable manual or automatic reconnection - includes warning
Load Control Mode	flash before disconnect and 6 minutes “grace” period.

Equalization Charge	User selectable manual or automatic equalization (every 30 days).
Charge Control Mode

Short Circuit Protection	Fully electronically protected with auto-reset.

Adjustable Control	Two user-adjustable, voltage setpoints for control of loads or charging
Setpoints (test points	sources (settings retained if battery is disconnected.)
provided for high
accuracy

Options

LCD Meter Panel	Back-lit, 32-character, alpha-numeric liquid crystal display panel for
(CM, CM/R-50,	remote (CM/R) or front mounting (CM) on the C-Series controller.
CM/R-100)

External Battery	Provides automatic adjustment of the charge control set point to the
Temperature Sensor	battery temperature (may be extended)
(BTS/15, BTS/35)

975-0004-01-02 Rev D

71

Image 91

Contents Series Multifunction DC Controller Page Series Multifunction DC Controller Date and Revision About XantrexTrademarks DisclaimerOrganization PurposeScope AudienceFollowing conventions are used in this guide Conventions UsedRelated Information Abbreviations and AcronymsPage General Safety Instructions Important Safety InstructionsViii Rev D Battery Safety InformationBattery Safety Information Page Contents Xii Rev D Batteries TroubleshootingSpecifications OperationDiversion Loads Warranty and Product InformationFigures Xvi Rev D Tables Xviii Introduction 1C-Series Multifunction DC Charge Controllers FeaturesLoad Control Mode Charge Control ModeOperating Modes Three-Stage Battery Charging Charge Control ModeBulk Stage Stage Battery Charging ProcessBattery Temperature Compensation Load Control ModeManual or Auto Equalization Charge Photovoltaic Charge Controller Controller FunctionsAutomatic PV Array Night Disconnect Diversion Controller4Diversion Controller Diversion LoadsLoad Controller Low Voltage Reconnect Low Voltage Disconnect6Decal Displaying Load Control Voltage Settings Optional AccessoriesInstallation Removing the Top Cover Pre-InstallationRemoving Knockouts 2C-Series Dimensions and Knockout Locations Not to Scale To mount the C-Series controller Mounting the Controller3Mounting the C-Series Multifunction DC Controller Jumper Settings Configuring the C-SeriesController5Circuit Board Components 1Factory Default Settings for C-Series ControllersVoltage Jumper Operating Mode Jumper8EQ/LVR Jumper and Reset Switch 9Bulk and Float Charge Potentiometers pots Adjusting the C-Series Voltage SettingsAdjusting the C-Series Voltage Settings 11Potentiometers with Decal for LVR and LVD Settings Setting Voltage Parameters for Load Control Mode12LVR and LVD Settings for Load Control Mode Setting Voltage Parameters for Alkaline Batteries Setting Voltage Parameters Diversion Control Mode14Voltage Settings with R46 Resistor Clipped To set Bulk voltage to 28.2 volts Using a Digital Voltmeter to Adjust Voltage SettingsTo test and adjust the voltage setting using a DVM To set the Bulk voltage to 14.4 voltsTo set Bulk voltage to 56.4 volts 15Test Points for Adjusting Voltage Using a DVMEqualization Charging 16Manual Equalization SettingsManual Equalization 17Front Panel LED and Reset Switch LocationAutomatic Equalization 18Auto Equalization SettingsTerminating the Equalization Process Temperature CompensationAutomatic Battery Temperature Compensation Temperature Compensation Based on Battery TypeLead-Acid Type Batteries 2Variances in Charging Voltage based on Battery Temperature Manual Battery Temperature Compensation 20Grounding the C-SeriesChassis GroundingDC Terminal Connector Locations WiringCurrent Rating Terminal Torque RequirementsC60 Models Minimum Recommended Wire GaugeSurge Protection C35 and C40 ModelsOver-current Protection 3Minimum Wire SizeMaximum One-way Distance and Wire Size Long-distance wire runsDistance in Feet meters 4One-Way Wire Distance and Wire SizeTo connect the C-Seriescontroller as a charge controller PV Charge Control Mode Wiring23PV Charge Control Mode Wiring To connect the C-Seriesas a diversion load controller Diversion Control Mode Wiring24Diversion Control Mode Wiring To connect the C-Series controller as a DC load controller DC Load Control Mode Wiring25Load Control Mode Wiring Installing a Digital Display Installing Optional AccessoriesTo install the BTS Installing the Battery Temperature SensorTo reinstall the faceplace on the C-Series controller Reinstalling the FaceplateOperation Basic Operation 1C-Series Status LED and Reset Button Location2C-Series Front Pa el Label LED Status IndicatorCharge Control or Diversion Control Indications Green 1Battery Voltage LED IndicatorsSolid Green Blinking GreenSolid Red Equalization Mode Indication Red/greenLoad Control Indications Red Blinking RedOver-temperature Condition Error Mode Indication OrangeOver-Current Condition Low-voltage Disconnect Condition Reconnecting to Loads3Reset Switch Reset SwitchPage 4Troubleshooting 1PV Charge Control Problems PV Charge Control TroubleshootingPV Charge Control Troubleshooting 2Diversion Control Problems Diversion Control TroubleshootingDiversion Control Troubleshooting 3Load Control Problems Load Control TroubleshootingASpecifications Table A-1Electrical Specifications Electrical SpecificationsTable A-2Features and Options Specifications Features and Options SpecificationsTable A-3Environmental Specifications Environmental SpecificationsBBatteries Deep-Cycle Batteries Battery TypesMaintenance-Free Batteries Automotive BatteriesSealed Batteries NiCad and NiFe Batteries Battery SizingEqualization Charging Rev D Table B-1Typical Bulk and Float Setpoints for Batteries Equalization Setpoints Non-Sealed Batteries OnlyPage CDiversion Loads Diversion Load Types Power DissipationDiversion Load Types Page Warranty Warranty and Product InformationProduct DisclaimerExclusions Return Material Authorization PolicyOut of Warranty Service Return ProcedureSerial Number on DC end Purchased From Purchase Date Information About Your SystemPage Index Index Page Xantrex Technology Inc