Cabletron Systems 9C300-1 manual Env

Page 26

9C300-1 Environmental Module Operation

Select <ACKNOWLEDGE> after reading all alarms to reset the front panel ALARM LED (red to green). Selecting <ACKNOWLEDGE> deletes all alarms and resets the alarm pending banner on line 4 of the non-interactive screens.

Select <EXIT> to return to the Main Screen.

The System Screen

Select the <SYSTEM> option ﬁeld in line 4 of the Main Screen, as shown in Figure 3-13,to access the System Screen as shown in Figure 3-15.This screen displays information speciﬁc to the MMAC-Plus chassis. Lines 1 and 2 display the MMAC-Plus chassis Internet Protocol (IP) address and Media Access Control (MAC) address.

Line 3 displays the current chassis hardware revision and serial number.

Line 4 lists the following ﬁve submenus. Access a speciﬁc submenu by selecting it on the screen.

<PWR>	Displays general power supply conﬁguration information,
	with the option to view statistics on speciﬁc power supply
	modules.
<ENV>	Displays environmental information about the chassis.
<COM>	Displays statistics and information about the front panel
	COM ports and EPIM on the Environmental Module.
<DIAGS>	Displays the results of power-up or restart diagnostic tests.
<BBU>	Displays status of BBUs, if they are installed.

CHASSIS IP ADDRESS xxx.xxx.xxx.xxx CHASSIS MAC ADDRESS xx-xx-xx-xx-xx-xx CHASSIS HW REV xxx SN xxxxxxxxxxxx <PWR> <ENV> <COM> <DIAGS> <BBU> <EXIT>

Figure 3-15. The System Screen

Select <EXIT> to return to the Main Screen.

3-14

Image 26

Contents MMAC-Plus 9C300-1 Environmental Module User’s Guide Page Page FCC Notice DOC NoticeContents Appendix a Epim Speciﬁcations Appendix B Uninterruptible Power Supply UPSChapter Speciﬁcations Using This Manual 9C300-1 Environmental ModuleOut-of-Band Management FeaturesSystem Cooling Flash Eeprom Environmental/Power MonitoringRelated Manuals Hot SwappingGetting Help Installing the 9C300-1 Environmental Module Installing the 9C300-1 Environmental ModuleInstalling the 9C300-1 Environmental Module 9C300-1 Environmental Module Operation Monitoring FunctionsExternal Ambient Temperature Temperature Range LCD DisplayFan Speed 9C300-1 Environmental Module and Fan TraySystem Voltages Internal Operating TemperatureSystem Humidity Humidity LCD DisplayLanview LEDs LED Color State DescriptionOut-of-Band Management COM1 and COM2 Ports Pin DescriptionEthernet Port Interface Module Epim LCD and KeypadSystem Screen Non-Interactive ModeNon-Interactive Mode Screens Utilization Screen Environment ScreenPower Screen System Banner ScreenInteractive Mode Interactive Mode ScreensAlarm Screen Main ScreenENV Supplies Installed 2 PWR Redundancy Status 1 on 2 on Exit Power Supply Speciﬁc ScreenCommunications Screen Diagnostic Module Selection Screen Diagnostic Results ScreenBBU Screen Module Selection ScreenFault Module Speciﬁc ScreenModule Environment Screen Module Memory ScreenModule Backplane Screen Environmental Module Speciﬁc ScreenEnvironmental Module Environment Screen LCD Contrast Adjustment Screen 9C300-1 Environmental Module Operation Safety ServicePhysical DimensionsWeight EnvironmentalEpim Speciﬁcations IntroductionEPIM-F1 and EPIM-F2 Parameter Typical Value Worst Worst Case BudgetEPIM-F1 and EPIM-F2 EPIM-F3 Parameter Typical Minimum Maximum Connector Type GroundingEPIM-A and EPIM-X AUI Port Pin Number RepresentsEpim Speciﬁcations Uninterruptible Power Supply UPS Connecting a UPS to an EMUninterruptible Power Supply UPS Conﬁguring COM Port for UPSVerifying Conﬁguration Monitoring UPSUninterruptible Power Supply UPS