Cabletron Systems 9C300-1 manual EPIM-F3

Page 42

EPIM Speciﬁcations

EPIM-F3

The EPIM-F3 supports Single Mode Fiber Optic cabling. It has an internal Cabletron Systems FOT-F™ Fiber Optic Transceiver and is equipped with ST Connectors. Figure A-3shows the EPIM-F3. Speciﬁcations for the EPIM-F3 are listed in Figure A-4and Table A-3.

Figure A-3. EPIM-F3

Maximum Sensitivity (-36.0)

Receive

Typical Sensitivity (-31.0)

Sensitivity

Minimum Sensitivity (-30.0)

Minimum Receive Input (-9.72)

Maximum

Typical Receive Input (-7.5)

Receive

Input Power

Maximum Receive Input (-6.99)

Transmitter Power*

Maximum Transmit Power (-12.0)

(At 25°C into

Typical Transmit Power (-15.5)

8.3/125∝m fiber)

Minimum Transmit Power (-21.0)

dBm

-40

-35

-30

-25

-20

-15

-10

-5

0

Less Power

More Power

* Transmit Power

Typical Power

Minimum Power

Maximum Power

Coefficient

-0.15dBm/°C

-0.12 dBm/°C

-0.18 dBm/°C

(See Note Below)

Figure A-4. EPIM-F3 Power and Sensitivity Speciﬁcations

NOTE

Transmitter Power decreases as temperatures rise and increases as temperatures fall. Use the Output Power Coefficient to calculate increased or decreased power output for your operating environment. For example, the typical power output at 25°C is -16.4 dBm. For a 4°C temperature increase, multiply the typical coefficient (-0.15 dBm) by four and add the result to typical output power (4 x -0.15 dBm + -16.4 = -17.0).

A-4

Image 42

Contents MMAC-Plus 9C300-1 Environmental Module User’s Guide Page Page FCC Notice DOC NoticeContents Appendix B Uninterruptible Power Supply UPS Chapter SpeciﬁcationsAppendix a Epim Speciﬁcations Using This Manual 9C300-1 Environmental ModuleFeatures System CoolingOut-of-Band Management Flash Eeprom Environmental/Power MonitoringRelated Manuals Hot SwappingGetting Help Installing the 9C300-1 Environmental Module Installing the 9C300-1 Environmental ModuleInstalling the 9C300-1 Environmental Module 9C300-1 Environmental Module Operation Monitoring FunctionsExternal Ambient Temperature Temperature Range LCD DisplayFan Speed 9C300-1 Environmental Module and Fan TraySystem Voltages Internal Operating TemperatureSystem Humidity Humidity LCD DisplayLanview LEDs LED Color State DescriptionOut-of-Band Management COM1 and COM2 Ports Pin DescriptionEthernet Port Interface Module Epim LCD and KeypadNon-Interactive Mode Non-Interactive Mode ScreensSystem Screen Utilization Screen Environment ScreenPower Screen System Banner ScreenInteractive Mode Interactive Mode ScreensAlarm Screen Main ScreenENV Supplies Installed 2 PWR Redundancy Status 1 on 2 on Exit Power Supply Speciﬁc ScreenCommunications Screen Diagnostic Module Selection Screen Diagnostic Results ScreenBBU Screen Module Selection ScreenFault Module Speciﬁc ScreenModule Environment Screen Module Memory ScreenModule Backplane Screen Environmental Module Speciﬁc ScreenEnvironmental Module Environment Screen LCD Contrast Adjustment Screen 9C300-1 Environmental Module Operation Safety ServicePhysical DimensionsWeight EnvironmentalEpim Speciﬁcations IntroductionEPIM-F1 and EPIM-F2 Parameter Typical Value Worst Worst Case BudgetEPIM-F1 and EPIM-F2 EPIM-F3 Parameter Typical Minimum Maximum Connector Type GroundingEPIM-A and EPIM-X AUI Port Pin Number RepresentsEpim Speciﬁcations Uninterruptible Power Supply UPS Connecting a UPS to an EMUninterruptible Power Supply UPS Conﬁguring COM Port for UPSVerifying Conﬁguration Monitoring UPSUninterruptible Power Supply UPS