Cabletron Systems 9C300-1 manual Environment Screen, Communications Screen

Page 28

9C300-1 Environmental Module Operation

The Environment Screen

Select <ENV> from the System Screen, as shown in Figure 3-15,to view environmental parameters of the MMAC-Plus.

Line 1 of this screen, as shown in Figure 3-18,displays the external temperature of the current chassis in both Fahrenheit and Celsius, and qualifies the temperature as COLD, COOL, NORM (normal), WARM, or HOT, based on system parameters.

Line 2 displays the current system non-condensing humidity level, qualified as STATIC RISK, NORM (normal), or MOIST, based on system parameters.

Line 3 displays the current fan speed of the Environmental Module cooling system as a percentage of maximum rotational velocity.

CHASSIS EXTERNAL TEMP xxx°F xx°C NORM

CHASSIS HUMIDITY xxx% NORM

FAN SPEED 1 xxx% 2 xxx% 3 xxx% 4 xxx%

<EXIT>

Figure 3-18. The Environment Screen

Select <EXIT> to return to the System Screen.

The Communications Screen

Select <COM> from the System Screen, as shown in Figure 3-15,to access

MMAC-Plus chassis communication port status information.

Line 1, as shown in Figure 3-19,displays the status of the Ethernet Port Interface Module (EPIM) as either ENABLED, DISABLED or N/A if not installed.

Line 2 displays the Port Administration status of COM port 1 (enabled or disabled), the application in use (such as Local Management (LM), SLIP, PPP or UPS), the baud rate of the attached device (a VT100 type terminal or modem) and the port operational status (active or inactive).

Line 3 displays the Port Administration status of COM port 2 in the same manner as described for line 2.

COMMUNICATIONS PORTS EPIM ENABLED

COM 1 ENABLED SLIP 9600 ACTIVE COM 2 ENABLED

<EXIT>

Figure 3-19. The Communications Screen

Select <EXIT> to return to the System Screen.

3-16

Page 27 Page 29
Image 28
Page 27 Page 29
Contents MMAC-Plus 9C300-1 Environmental Module User’s Guide Page Page FCC Notice DOC NoticeContents Chapter Specifications Appendix B Uninterruptible Power Supply UPSAppendix a Epim Specifications Using This Manual 9C300-1 Environmental ModuleSystem Cooling FeaturesOut-of-Band Management Environmental/Power Monitoring Related ManualsFlash Eeprom Hot SwappingGetting Help Installing the 9C300-1 Environmental Module Installing the 9C300-1 Environmental ModuleInstalling the 9C300-1 Environmental Module 9C300-1 Environmental Module Operation Monitoring FunctionsExternal Ambient Temperature Temperature Range LCD DisplayFan Speed 9C300-1 Environmental Module and Fan TrayInternal Operating Temperature System HumiditySystem Voltages Humidity LCD DisplayLanview LEDs LED Color State DescriptionOut-of-Band Management COM1 and COM2 Ports Pin DescriptionEthernet Port Interface Module Epim LCD and KeypadNon-Interactive Mode Screens Non-Interactive ModeSystem Screen Utilization Screen Environment ScreenPower Screen System Banner ScreenInteractive Mode Interactive Mode ScreensAlarm Screen Main ScreenENV Supplies Installed 2 PWR Redundancy Status 1 on 2 on Exit Power Supply Specific ScreenCommunications Screen Diagnostic Module Selection Screen Diagnostic Results ScreenBBU Screen Module Selection ScreenFault Module Specific ScreenModule Environment Screen Module Memory ScreenModule Backplane Screen Environmental Module Specific ScreenEnvironmental Module Environment Screen LCD Contrast Adjustment Screen 9C300-1 Environmental Module Operation Safety ServiceDimensions WeightPhysical EnvironmentalEpim Specifications IntroductionEPIM-F1 and EPIM-F2 Parameter Typical Value Worst Worst Case BudgetEPIM-F1 and EPIM-F2 EPIM-F3 Parameter Typical Minimum Maximum Connector Type GroundingEPIM-A and EPIM-X AUI Port Pin Number RepresentsEpim Specifications Uninterruptible Power Supply UPS Connecting a UPS to an EMUninterruptible Power Supply UPS Configuring COM Port for UPSVerifying Configuration Monitoring UPSUninterruptible Power Supply UPS
Top Page Image Contents