Extron electronic DVS 304 manual Picture-in-picture mode, Changing the input

Page 27

Picture-in-picture mode

The DVS 304 can display two image sources on the screen simultaneously. Keep in mind that when using the PIP feature, one image source must be low-resolution (composite, S-video, YUVi and RGBcvS) video, while the other must be high resolution (YUVp/HDTV, RGB scaled, SDI) video. If these conditions are not met (for example, two low resolution video inputs or two high resolution inputs are selected), the PIP mode will exit.

To go into picture-in-picture mode, do the following:

1.Select an input for the main window.

2.Define the size of the main window before starting PIP mode.

3.Activate the PIP mode via an SIS command or IR remote; specify the PIP window input.

DVS 304 checks the input format for the PIP window and returns an error message if an invalid selection is made.

NOTE: For quick sizing setup, use the 16*# X10% SIS command to set different sizes for the PIP window.

When the PIP mode is active, note the following:

The LED for the main window input is ON.

The parameters of the PIP window are adjustable from the front panel or by SIS commands only.

Any change in configuration (except positioning) of the PIP window is saved to that input even after the PIP mode is not longer active.

The PIP window input is listed under the default cycle on front panel menu, as shown below.

When the PIP window is active, size, position, and picture controls all apply to the PIP window. The main window settings cannot be modified while the PIP window is active. The PIP size and position can be adjusted with the same front panel controls or SIS commands used to adjust the main image.

Default Cycle

2 sec.

INPUT 1

COMPOSITE

2 sec.

 

 

PIP WINDOW

 

 

INPUT 2

 

 

 

 

 

 

 

2 sec.

 

 

OUTPUT

 

 

1024 x 768@60

 

 

 

 

 

 

 

Figure 22. PIP Sequence

If the PIP window source is not active, the PIP mode exits until an active signal is detected. When the main window source is removed, a black background is displayed.

Changing the input

To change the input for the PIP and/or main window, determine if the corresponding input is a low or high resolution.

If your main window image is from a low resolution source, switch to another low resolution input from the front panel.

DVS 304 Series • Operation

22

Image 27
Contents DVS 304 Series Vorsicht AchtungPrecaucion AvertissementExtron Electronics. All rights reserved FCC Class a NoticeContents Menu System Introduction DVS 304 Series DescriptionDVS 304 Models Four inputs FeaturesMemory and input presets DVS 304 DVI ModelsBuffered video outputs Controlling the DVS 304 DevicesOptions and Accessories Rear Panel Cabling CablingVideo PinWiring the RJ-45 No connection Ground Signal ground InputPin RS-232 Function Description InputFront Panel Overview OperationBetween them Menus, Configuration, and AdjustmentsMenu Navigation Using Front Panel Controls Menu OverviewMain Menu Start Auto Image Input ConfigurationInput 4 video type Input 1 video typeInput 2 video type Input 3 video typePicture Control Output ConfigurationResolutions and Refresh Rates Output FormatSync Polarity Audio Configuration Audio Models Only Memory PresetMemory Preset Per input Total Input preset Save Memory PresetClear CLR memory preset Recalling a presetAdvanced Configuration IP ConfigurationAuto-Image Blue modeAuto switch mode RGB delayRefresh Lock Enhance modeOSD label Test patternAuto Memory Per input Total Aspect ModeAuto Memory and Auto Image Features Auto MemoryChanging the input Picture-in-picture modeResetting an Input Using the swap featureExit Menu Resetting the Unit DVS 304 Reset Mode SummaryMode Activation Result Purpose and Notes Front Panel Lockout Executive Modes System ResetDVS 304 Devices Connected to a Matrix Switcher Setting up the DVS to Work with a Matrix SwitcherFrom the Tools menu, select Sync Scaler to Matrix Switcher Removing the Sync to Matrix Script Sync DVS 304 to Matrix Switcher window opensDVS 304 Series Operation Pin RS-232 Function Description SIS Communication ControlError Numbers Password InformationError Responses Error Response ReferencesCommand and Responses Using the Command and Response TablesTelnet Web Browser Symbol Definitions Password is also removed X7@ = Input selection 2 or SIS Command Edid Table see SIS Command and Response Table EI*X10*EDIDX6 Input aspect ratioVideo mute Edid emulation for input 4 DVI models onlyBrightness Color available for PAL and Ntsc onlyTint available for Ntsc composite and S-video only ContrastOutput sync format Zoom modePan Output scaler rateAudio mute audio models only Memory presets inputs 1 toInput presets input 4 only Write and read input preset name inputs 4 presets onlyTest pattern Volume control audio models onlyRGB delay time Auto switch modeView internal temperature PIP modeSwap when PIP mode is On PIP mode audio follow audio model onlySDI field flip Front panel security lockout Executive ModeEnhanced mode Aspect modeFirmware version requests SIS Command and Response Table for IP Control PortEthernet data port E0 *X6 TCInformation requests Event controlEAE X4&SM Web browser specific commandIP setup commands MailECZ E #CZWX1CS ECS EECG EMH WX3#CURe-map port designations EMTListing connections EMDFile commands Directory commandsEZI File erase commandsReset ZAP/erase Commands EZASignal Processing Products Control Program Installing the SoftwareInstallation from the DVD Starting the Sppcp Installation from the Web SiteOrientation Using the SppcpSppcp Menus File menuOptions menu Tools menu Sync to Matrix Switcher WindowSystems Settings Window Firmware Loader Window Process Running Help menuControl Tab Window Control TabI/O Configuration Tab Window Configuration TabStatus Bar Advanced Settings TabEthernet Control Accessing the Default Web PagesStatus tab displays the System Status page for the DVS Navigating the Default Web PagesStatus System StatusSystem Settings ConfigurationIP Address Scaler Settings Scaler SettingsPasswords PasswordsFirmware Upgrade Firmware UpgradeWeb Server File Management File ManagementUser Control ControlPresets PresetsDefault Cycle Menu Menu SystemMain Menu Start Auto Image Menu Input Configuration MenuOutput Configuration Menu Audio Configuration MenuMemory Preset Menu Advanced Configuration Menu IP Configuration MenuEnable Executive Mode Executive Mode MenuVideo Processing SpecificationsReference Material Video InputSync Audio DVS 304 A, DVS 304 AD, DVS 304 DVI A, DVS 304 DVI ADControl/Remote Decoder/Scaler General Description Part Number Models Part Numbers and AccessoriesIncluded Parts Optional PartsInstallation of the SDI card Serial Digital Interface SDI Card InstallationDVS 304 Series Reference Information DVS 304 Series Reference Information Europe USA, Canada, South America Japan Central AmericaEurope, Africa, and the Middle China East Asia Middle East
Related manuals
Manual 96 pages 15.78 Kb