Extron electronic DVS 304 manual Tools menu, Sync to Matrix Switcher Window

Page 63

Tools menu

Click on this to open a drop-down box displaying

nine selectable options: Data View/Trace Window...

Sync Scaler to Matrix Switcher..., System Settings...,

Reset (has a secondary drop down box), and Update

Firmware....

Data View/Trace Window... — Select this to open a separate window in which the transmit and receive (Tx/Rx)

data between the control software on the host PC and the

DVS can be viewed in ASCII format (see figure at right).

During data transmission and receipt, the data tracer window is constantly updated.

Click Save to save the Data trace in a log file format.

Click Clear to erase all the data in the data tracer window. To close the window, click Close or the X in the top right corner of the window.

Sync Scaler to Matrix Switcher — Select this to open a secondary window. Within that window enter the IP address of the matrix switcher to which the DVS is connected. If required enter the password, then click Connect to Matrix. Select the output number from the Matrix Output to DVS drop-down list and click

Take. The Matrix Status section displays the matrix output that is being monitored and the tied input. The DVS Input #4 section displays the current status of the input being used.

Figure 31. Sync to Matrix Switcher Window

NOTE: The matrix switcher must be connected to via a configured input on the

DVS 304. See page 26 for information.

The matrix and the DVS must to be connected to an active network at all

times to allow the products to remain synchronized. If the connection is

lost, the script needs to be restarted by either sending the SIS command or

by power cycling the DVS.

Click Refresh Status to update the status of the matrix switcher. Refreshing the status returns updated information about which scaler input is tied to a particular matrix output.

DVS 304 Series • SIS Communication and Control

58

Image 63
Contents DVS 304 Series Vorsicht AchtungPrecaucion AvertissementExtron Electronics. All rights reserved FCC Class a NoticeContents Menu System Introduction DVS 304 Series DescriptionDVS 304 Models Four inputs FeaturesMemory and input presets DVS 304 DVI ModelsBuffered video outputs Controlling the DVS 304 DevicesOptions and Accessories Rear Panel Cabling CablingVideo PinWiring the RJ-45 No connection Ground Signal ground InputPin RS-232 Function Description InputFront Panel Overview OperationBetween them Menus, Configuration, and AdjustmentsMenu Navigation Using Front Panel Controls Menu OverviewMain Menu Start Auto Image Input ConfigurationInput 4 video type Input 1 video typeInput 2 video type Input 3 video typePicture Control Output ConfigurationResolutions and Refresh Rates Output FormatSync Polarity Audio Configuration Audio Models Only Memory PresetMemory Preset Per input Total Input preset Save Memory PresetClear CLR memory preset Recalling a presetAdvanced Configuration IP ConfigurationAuto-Image Blue modeAuto switch mode RGB delayRefresh Lock Enhance modeOSD label Test patternAuto Memory Per input Total Aspect ModeAuto Memory and Auto Image Features Auto MemoryChanging the input Picture-in-picture modeResetting an Input Using the swap featureExit Menu Resetting the Unit DVS 304 Reset Mode SummaryMode Activation Result Purpose and Notes Front Panel Lockout Executive Modes System ResetDVS 304 Devices Connected to a Matrix Switcher Setting up the DVS to Work with a Matrix SwitcherFrom the Tools menu, select Sync Scaler to Matrix Switcher Removing the Sync to Matrix Script Sync DVS 304 to Matrix Switcher window opensDVS 304 Series Operation Pin RS-232 Function Description SIS Communication ControlError Numbers Password InformationError Responses Error Response ReferencesCommand and Responses Using the Command and Response TablesTelnet Web Browser Symbol Definitions Password is also removed X7@ = Input selection 2 or SIS Command Edid Table see SIS Command and Response Table EI*X10*EDIDX6 Input aspect ratioVideo mute Edid emulation for input 4 DVI models onlyBrightness Color available for PAL and Ntsc onlyTint available for Ntsc composite and S-video only ContrastOutput sync format Zoom modePan Output scaler rateAudio mute audio models only Memory presets inputs 1 toInput presets input 4 only Write and read input preset name inputs 4 presets onlyTest pattern Volume control audio models onlyRGB delay time Auto switch modeView internal temperature PIP modeSwap when PIP mode is On PIP mode audio follow audio model onlySDI field flip Front panel security lockout Executive ModeEnhanced mode Aspect modeFirmware version requests SIS Command and Response Table for IP Control PortEthernet data port E0 *X6 TCInformation requests Event controlEAE X4&SM Web browser specific commandIP setup commands MailECZ E #CZWX1CS ECS EECG EMH WX3#CURe-map port designations EMTListing connections EMDFile commands Directory commandsEZI File erase commandsReset ZAP/erase Commands EZASignal Processing Products Control Program Installing the SoftwareInstallation from the DVD Starting the Sppcp Installation from the Web SiteOrientation Using the SppcpSppcp Menus File menuOptions menu Tools menu Sync to Matrix Switcher WindowSystems Settings Window Firmware Loader Window Process Running Help menuControl Tab Window Control TabI/O Configuration Tab Window Configuration TabStatus Bar Advanced Settings TabEthernet Control Accessing the Default Web PagesStatus tab displays the System Status page for the DVS Navigating the Default Web PagesStatus System StatusSystem Settings ConfigurationIP Address Scaler Settings Scaler SettingsPasswords PasswordsFirmware Upgrade Firmware UpgradeWeb Server File Management File ManagementUser Control ControlPresets PresetsDefault Cycle Menu Menu SystemMain Menu Start Auto Image Menu Input Configuration MenuOutput Configuration Menu Audio Configuration MenuMemory Preset Menu Advanced Configuration Menu IP Configuration MenuEnable Executive Mode Executive Mode MenuVideo Processing SpecificationsReference Material Video InputSync Audio DVS 304 A, DVS 304 AD, DVS 304 DVI A, DVS 304 DVI ADControl/Remote Decoder/Scaler General Description Part Number Models Part Numbers and AccessoriesIncluded Parts Optional PartsInstallation of the SDI card Serial Digital Interface SDI Card InstallationDVS 304 Series Reference Information DVS 304 Series Reference Information Europe USA, Canada, South America Japan Central AmericaEurope, Africa, and the Middle China East Asia Middle East
Related manuals
Manual 96 pages 15.78 Kb