ATTO Technology 1500D/E, 1550D/E operation manual Exhibit 1.3-1 iPBridge 1550E board layout

Page 17

Exhibit 1.3-1 iPBridge 1550E board layout

Mounting hole

Reset

SCSI Activity

LED

pin 1

Serial port

SCSI Activity

Mounting holeFault LEDMounting hole

LED

4-pin power connector

Mounting hole

Ethernet port

SCSI port

SCSI Activity LED

Mounting hole

Exhibit 1.3-2 iPBridge 1550E board profile and dimensions

E t h e r n e t P o r t

S C S I P o r t

P o w e r

. 5 3 6

. 3 4 3

L o n g B o a r d E d g e

. 3 1 3

R J - 1 1 P o r t

E t h e r n e t P o r t

. 3 3 1

. 2 7 6	S h o r t B o a r d E d g e

Installation instructions

1Install the iPBridge 1550E in the target device using the mounting holes in the board. (See the board layout diagram in Exhibit )

2Connect SCSI devices to the iPBridge. (See Connecting SCSI devices to the SCSI port on page 11)

3Connect the iPBridge to your SAN: attach CAT 6 or CAT 5E cables to the Ethernet port on the iPBridge or connect an RJ11 and adapter crossover serial cable (null modem) between the iPBridge serial port and one of the computer's serial COM ports.

4Connect the power connector and power up.

5Boot the computers on the SAN.

6Access iPBridge Services via the Ethernet port. (See Configuring the iPBridge on page 13) or the serial port (Connecting using the serial port on page 14)

7Verify that the bridge can be accessed on the local Ethernet network by using the Ping utility. (See Step 7 on page 15)

8Set up the configuration for the devices connected to the iPBridge (See Managing the iPBridge on page 17.)

9Power cycle the iPBridge. The iPBridge will automatically map the devices on startup

8 Installation: ATTO iPBridge 1550E

Image 17

Contents IPBridgeTM 1500D/E IPBridgeTM 1550D/E Page Page Contents Connecting Scsi devices to the Scsi port Serial port configuration commands Mapping commands Term Definition GlossaryIntelligent Bridging Architecture, the engine Introduction IPBridge 1550 features Setting up the iPBridgeIPBridge1500 features Scsi Possible SAN/NAS ConfigurationAtto iPBridge 1500E Pin outs of the RJ11 connector, part number CBL-0911-001Exhibit 1.1-1 iPBridge 1500E board layout Installation instructionsAtto iPBridge 1500D Exhibit 1.2-1 iPBridge 1500D back panel Atto iPBridge 1550E Exhibit 1.3-1 iPBridge 1550E board layout Atto iPBridge 1550D Exhibit 1.4-1 iPBridge 1550D back panel To set Scsi port bus speed and transfer rates Connecting Scsi devices to the Scsi portTo connect Scsi devices to the Atto iPBridge Examples CablingCable types To find the iPBridge Configuring the iPBridgeConnecting using the GbE port Connecting using the serial port Using Atto ExpressNAVTo optimize ExpressNAV in Internet Explorer Select Internet OptionsEnter Using TelnetTo connect using Telnet Installation Configuration Scsi configuration Change default username, passwordTo change the default administrator password Managing the iPBridgeISCSI configuration Ethernet port configurationOEM configuration services MappingExpressNAV provides web-based interface Serial Port ConfigurationStatus To open an ExpressNAV sessionAdvanced CLI Configuration Bridge ConfigurationTo use the Advanced Configuration Restart FirmwareCLI provides ASCII-based interface Get Set Command Parameter 1 ParameterCommand conventions Configuration & Management CLI Command Defaults Example CLI commands summaryOEM configuration file Defaults Limits General use commands VerboseMode From information commands. Choices are enabled or disabledDiagnostic commands RouteDisplay CLI Error MessagesSCSIPortList SCSITargetsMaintenance commands Configuration CLI Scsi configuration commands SpeedWrite SerialPortEcho Serial port configuration commandsSerialPortBaudRate Configuration CLI Ethernet commands ReadOnlyUsername ReadOnlyPasswordISCSI commands MultiTargetMode ISNSServerRoute Mapping commandsAutoMap Configuration CLI Privileged OEM configuration services ModelNumber OEM Config file supported commandsProductID VendorIDUse Command Line Interface Single target modeMapping devices Node namesMapping single vs. multiple target mode Use the ExpressNAV interface Multiple target modeTo remove an iSCSITarget Example\bridgefirmware\I1500110.ima Updating firmwareTo use FTP over GbE to flash new firmware into the iPBridge Configuration & Management firmware update Appendix a Safety standards and compliances European Standards PWRA-0000-FRUPower Module for Atto FC Rack System FC Rack Enclosures with Power SuppliesAtto iPBridge 2500C Atto iPBridge 1500ECables/SCSI AccessoriesAppendix C Contact Atto Technology, Inc