ATTO Technology 1550D/E, 1500D/E operation manual ExpressNAV provides web-based interface, Status

Page 28

2.1 ExpressNAV provides web-based interface

Each page in the ATTO ExpressNAV interface provides information and/or configuration parameters based on a specific topic.

ATTO ExpressNAV is the recommended management tool for the iPBridge. It is a web- based graphical user interface (GUI) that allows you to manage the iPBridge by clicking choices and commands in traditional GUI fashion or by entering CLI commands directly, as you would in a terminal emulation session.

Before opening an ExpressNAV session, you must install the ExpressNAV interface. Refer to Configuring the iPBridge on page 13.

To open an ExpressNAV session

1Point your browser at the IP address of the iPBridge. Refer to Configuring the iPBridge on page 13.

2The ExpressNAV home page is displayed. Click Enter.

3Enter the username and password values.

Note

The default values are username: “root” and

password: “Password”. The username is case insensitive and password is case sensitive.

The Status page appears.

Each page can be reached through the menu at the side of each page An image on each page’s header shows each port in the product faceplate. Each port is clickable and will also take you to the appropriate page.

Status

Displays iPBridge information

•Vendor ID

•Product ID

•Firmware revision number

•Serial number

•Ethernet port IP addresses

•Ethernet port status

Serial Port Configuration

Configure the baud rate and echo parameters. See Serial port configuration commands on page 33 for details on each option.

Ethernet Port Configuration Configures each port independently for the following parameters

•Enable/disable DHCP

•IP address

•IP gateway

•IP subnet mask

•Ethernet speed

•MTU

Note

Ethernet speed settings in the host must be the same as Ethernet speed settings in the iPBridge. The iPBridge default Ethernet speed is auto: your host must be set to auto. If you set Ethernet speed to 10, your host must be set to Ethernet speed 10, half duplex. If you set Ethernet speed to 100, your host must be set to Ethernet speed 100, half duplex.

See Ethernet commands on page 35 for details on each parameter.

SCSI Configuration

Displays include a list of attached devices for the SCSI bus. Configurable options are

•Port Bus Speed

•Synchronous Transfer

•Wide Transfer

•Initiator ID

•Bus Reset on Startup

•Bus Termination

•SCSI Port Reset

See SCSI configuration commands on page 31 for details on each parameter.

19

ATTO Technology Inc. iPBridge Installation and Operation Manual

Page 27 Page 29
Image 28
Page 27 Page 29
Contents IPBridgeTM 1500D/E IPBridgeTM 1550D/E Page Page Contents Connecting Scsi devices to the Scsi port Serial port configuration commands Mapping commands Intelligent Bridging Architecture, the engine GlossaryTerm Definition Introduction IPBridge1500 features Setting up the iPBridgeIPBridge 1550 features Possible SAN/NAS Configuration ScsiPin outs of the RJ11 connector, part number CBL-0911-001 Atto iPBridge 1500EInstallation instructions Exhibit 1.1-1 iPBridge 1500E board layoutAtto iPBridge 1500D Exhibit 1.2-1 iPBridge 1500D back panel Atto iPBridge 1550E Exhibit 1.3-1 iPBridge 1550E board layout Atto iPBridge 1550D Exhibit 1.4-1 iPBridge 1550D back panel To connect Scsi devices to the Atto iPBridge Connecting Scsi devices to the Scsi portTo set Scsi port bus speed and transfer rates Cable types CablingExamples Connecting using the GbE port Configuring the iPBridgeTo find the iPBridge Using Atto ExpressNAV Connecting using the serial portTo optimize ExpressNAV in Internet Explorer Select Internet OptionsTo connect using Telnet Using TelnetEnter Installation Configuration Change default username, password Scsi configurationTo change the default administrator password Managing the iPBridgeEthernet port configuration ISCSI configurationOEM configuration services MappingSerial Port Configuration ExpressNAV provides web-based interfaceStatus To open an ExpressNAV sessionBridge Configuration Advanced CLI ConfigurationTo use the Advanced Configuration Restart FirmwareCommand conventions Get Set Command Parameter 1 ParameterCLI provides ASCII-based interface Configuration & Management CLI CLI commands summary Command Defaults ExampleOEM configuration file Defaults Limits General use commands From information commands. Choices are enabled or disabled VerboseModeDiagnostic commands CLI Error Messages RouteDisplaySCSIPortList SCSITargetsMaintenance commands Configuration CLI Scsi configuration commands SpeedWrite SerialPortBaudRate Serial port configuration commandsSerialPortEcho Configuration CLI Ethernet commands ReadOnlyPassword ReadOnlyUsernameISCSI commands ISNSServer MultiTargetModeAutoMap Mapping commandsRoute Configuration CLI Privileged OEM configuration services OEM Config file supported commands ModelNumberProductID VendorIDSingle target mode Use Command Line InterfaceMapping devices Node namesMapping single vs. multiple target mode Multiple target mode Use the ExpressNAV interfaceExample To remove an iSCSITargetTo use FTP over GbE to flash new firmware into the iPBridge Updating firmware\bridgefirmware\I1500110.ima Configuration & Management firmware update Appendix a Safety standards and compliances European Standards FC Rack Enclosures with Power Supplies PWRA-0000-FRUPower Module for Atto FC Rack SystemAtto iPBridge 2500C Atto iPBridge 1500EAccessories Cables/SCSIAppendix C Contact Atto Technology, Inc
Top Page Image Contents