ATTO Technology 1500D/E, 1550D/E operation manual Exhibit 1.4-1 iPBridge 1550D back panel

Page 19

Exhibit 1.4-1 iPBridge 1550D back panel

air vents

power

connector

Ethernet	Ethernet	SCSI port	Power
speed LED	activity LED	activity LED	LED

Installation instructions

1Place the iPBridge 1550D where you want it.

2Connect SCSI devices to the iPBridge. (See Connecting SCSI devices to the SCSI port on page 11)

3Connect the iPBridge to your SAN: attach CAT 6 or CAT 5E cables to the Ethernet port on the iPBridge or connect an RJ11 and adapter crossover serial cable (null modem) between the iPBridge serial port and one of the computer's serial COM ports.

4Connect the power connector and power up.

5Boot the computers on the SAN.

6Access iPBridge Services via the Ethernet port. (See Configuring the iPBridge on page 13) or the serial port (Connecting using the serial port on page 14)

7Verify that the bridge can be accessed on the local Ethernet network by using the Ping utility. (See Step 7 on page 15)

8Set up the configuration for the devices connected to the iPBridge (See Managing the iPBridge on page 17.)

9Power cycle the iPBridge. The iPBridge will automatically map the devices on startup.

10 Installation: ATTO iPBridge 1550D

Image 19

Contents IPBridgeTM 1500D/E IPBridgeTM 1550D/E Page Page Contents Connecting Scsi devices to the Scsi port Serial port configuration commands Mapping commands Intelligent Bridging Architecture, the engine GlossaryTerm Definition Introduction IPBridge1500 features Setting up the iPBridgeIPBridge 1550 features Scsi Possible SAN/NAS ConfigurationAtto iPBridge 1500E Pin outs of the RJ11 connector, part number CBL-0911-001Exhibit 1.1-1 iPBridge 1500E board layout Installation instructionsAtto iPBridge 1500D Exhibit 1.2-1 iPBridge 1500D back panel Atto iPBridge 1550E Exhibit 1.3-1 iPBridge 1550E board layout Atto iPBridge 1550D Exhibit 1.4-1 iPBridge 1550D back panel To connect Scsi devices to the Atto iPBridge Connecting Scsi devices to the Scsi portTo set Scsi port bus speed and transfer rates Cable types CablingExamples Connecting using the GbE port Configuring the iPBridgeTo find the iPBridge Select Internet Options Using Atto ExpressNAVConnecting using the serial port To optimize ExpressNAV in Internet ExplorerTo connect using Telnet Using TelnetEnter Installation Configuration Managing the iPBridge Change default username, passwordScsi configuration To change the default administrator passwordMapping Ethernet port configurationISCSI configuration OEM configuration servicesTo open an ExpressNAV session Serial Port ConfigurationExpressNAV provides web-based interface StatusRestart Firmware Bridge ConfigurationAdvanced CLI Configuration To use the Advanced ConfigurationCommand conventions Get Set Command Parameter 1 ParameterCLI provides ASCII-based interface Configuration & Management CLI Command Defaults Example CLI commands summaryOEM configuration file Defaults Limits General use commands VerboseMode From information commands. Choices are enabled or disabledDiagnostic commands SCSITargets CLI Error MessagesRouteDisplay SCSIPortListMaintenance commands Configuration CLI Scsi configuration commands SpeedWrite SerialPortBaudRate Serial port configuration commandsSerialPortEcho Configuration CLI Ethernet commands ReadOnlyUsername ReadOnlyPasswordISCSI commands MultiTargetMode ISNSServerAutoMap Mapping commandsRoute Configuration CLI Privileged OEM configuration services VendorID OEM Config file supported commandsModelNumber ProductIDNode names Single target modeUse Command Line Interface Mapping devicesMapping single vs. multiple target mode Use the ExpressNAV interface Multiple target modeTo remove an iSCSITarget ExampleTo use FTP over GbE to flash new firmware into the iPBridge Updating firmware\bridgefirmware\I1500110.ima Configuration & Management firmware update Appendix a Safety standards and compliances European Standards Atto iPBridge 1500E FC Rack Enclosures with Power SuppliesPWRA-0000-FRUPower Module for Atto FC Rack System Atto iPBridge 2500CCables/SCSI AccessoriesAppendix C Contact Atto Technology, Inc