ATTO Technology 1550D/E, 1500D/E Managing the iPBridge, Change default username, password

Page 26

2 Managing the iPBridge

Default values are appropriate for most configurations, but may be modified for your needs using CLI commands or ATTO ExpressNAV.

ATTO iPBridge Services configures and tunes the iPBridge for many different environments and applications, updates the firmware, configures the addresses of the connected SCSI devices, monitors status and reports on hardware.

Communicate with the ATTO iPBridge through the GbE management port using ATTO ExpressNAV or Telnet or through the serial port using standard terminal emulation software.

Note

ATTO ExpressNAV is the recommended management tool for the iPBridge

•Refer to Configuring the iPBridge on page 13 to set up ExpressNAV and Telnet.

•To use ExpressNAV, refer to ExpressNAV provides web-based interface on page 19.

•To use the Command Line Interface during a Telnet session or from the Advanced Page of ExpressNAV, refer to CLI provides ASCII-based interface on page 21.

CAUTION

Any changes must be saved and will not take effect until the ATTO iPBridge is restarted.

Some completed configuration commands do not take effect until you have issued the saveConfiguration command. When this is the case, the Ready prompt will be followed by asterisk. You can issue the saveConfiguration command after each such configuration command or wait until you have entered all the parameters you wish to change.

Change default username, password

It is best practice to change the default username and password after you have configured your

iPBridge. If you do so, record the new username and password in a convenient place.

To change the default administrator password

1If you have not already, open an ExpressNAV session.

For instructions, refer to To open an ExpressNAV session on page 19.

2Click Bridge.

The Bridge Configuration page is displayed. The username that you are currently logged in with is displayed in the Username text box.

3Enter appropriate information into the Username, Current Password, Old Password, New Password, and Confirm Password text boxes.

Note

The username is case insensitive and password is case sensitive.

4Click Submit.

5The username and password for all Telnet, FTP and ATTO ExpressNAV sessions is changed.

You may also set a read only password or a read only username. Refer to General use commands on page 25.

SCSI configuration

Default values are appropriate for most configurations, but may be modified for your needs using CLI commands. Refer to SCSI configuration commands on page 31 for more information.

You may change the InitID, the port bus speed, terminaton, sync transfers, type of transfers, performance speed and the way the ports respond to resets. You may also get information on these parameters, a list of SCSI ports and their time outs.

17

ATTO Technology Inc. iPBridge Installation and Operation Manual

Page 25 Page 27
Image 26
Page 25 Page 27
Contents IPBridgeTM 1500D/E IPBridgeTM 1550D/E Page Page Contents Connecting Scsi devices to the Scsi port Serial port configuration commands Mapping commands Term Definition GlossaryIntelligent Bridging Architecture, the engine Introduction IPBridge 1550 features Setting up the iPBridgeIPBridge1500 features Possible SAN/NAS Configuration ScsiPin outs of the RJ11 connector, part number CBL-0911-001 Atto iPBridge 1500EInstallation instructions Exhibit 1.1-1 iPBridge 1500E board layoutAtto iPBridge 1500D Exhibit 1.2-1 iPBridge 1500D back panel Atto iPBridge 1550E Exhibit 1.3-1 iPBridge 1550E board layout Atto iPBridge 1550D Exhibit 1.4-1 iPBridge 1550D back panel To set Scsi port bus speed and transfer rates Connecting Scsi devices to the Scsi portTo connect Scsi devices to the Atto iPBridge Examples CablingCable types To find the iPBridge Configuring the iPBridgeConnecting using the GbE port To optimize ExpressNAV in Internet Explorer Using Atto ExpressNAVConnecting using the serial port Select Internet OptionsEnter Using TelnetTo connect using Telnet Installation Configuration To change the default administrator password Change default username, passwordScsi configuration Managing the iPBridgeOEM configuration services Ethernet port configurationISCSI configuration MappingStatus Serial Port ConfigurationExpressNAV provides web-based interface To open an ExpressNAV sessionTo use the Advanced Configuration Bridge ConfigurationAdvanced CLI Configuration Restart FirmwareCLI provides ASCII-based interface Get Set Command Parameter 1 ParameterCommand conventions Configuration & Management CLI CLI commands summary Command Defaults ExampleOEM configuration file Defaults Limits General use commands From information commands. Choices are enabled or disabled VerboseModeDiagnostic commands SCSIPortList CLI Error MessagesRouteDisplay SCSITargetsMaintenance commands Configuration CLI Scsi configuration commands SpeedWrite SerialPortEcho Serial port configuration commandsSerialPortBaudRate Configuration CLI Ethernet commands ReadOnlyPassword ReadOnlyUsernameISCSI commands ISNSServer MultiTargetModeRoute Mapping commandsAutoMap Configuration CLI Privileged OEM configuration services ProductID OEM Config file supported commandsModelNumber VendorIDMapping devices Single target modeUse Command Line Interface Node namesMapping single vs. multiple target mode Multiple target mode Use the ExpressNAV interfaceExample To remove an iSCSITarget\bridgefirmware\I1500110.ima Updating firmwareTo use FTP over GbE to flash new firmware into the iPBridge Configuration & Management firmware update Appendix a Safety standards and compliances European Standards Atto iPBridge 2500C FC Rack Enclosures with Power SuppliesPWRA-0000-FRUPower Module for Atto FC Rack System Atto iPBridge 1500EAccessories Cables/SCSIAppendix C Contact Atto Technology, Inc
Top Page Image Contents