ATTO Technology 1550D/E, 1500D/E operation manual Using Telnet, To connect using Telnet, Enter

Page 24

set ipgateway dp0 e.f.g.h

where e.f.g.h is a valid gateway.

9 To save the settings, type

saveconfiguration restart

The iPBridge will save the changes and perform a restart.

10Once rebooted, verify that the iPBridge can be accessed by your network using standard network techniques such as the ping command.

Using Telnet

Up to three Telnet sessions can be conducted simultaneously. Whichever session issues the first “set” Command Line Interface command (refer to CLI provides ASCII-based interface on page 21) can continue to issue set commands, while the other sessions can only issue “get” commands or display information. Once a connection is established, refer to CLI commands summary on page 23 for lists of valid commands.

To connect using Telnet

1Connect through the GbE port as outlined in Connecting using the GbE port using a computer on the same Ethernet network.

2Start a Telnet session.

Note

There is more than one way to connect to the iPBridge using a telnet program.Your telnet program may operate differently than in the following instructions.

3Obtain the iPAddress for the iPBridge from your system administrator. The default address is

10.0.0.3

15

4 At the telnet prompt, issue the open command:

telnet > open x.x.x.x

where x.x.x.x is the IP address of the iPBridge.

5If you have to specify a port type, enter the port type “telnet” and the terminal type “vt100”.

port type:telnet terminal type: vt100

6Enter the default values for the username, “root”, and the password, “Password”.

Note

The username is case insensitive and password is case sensitive.

7To verify that you have connected successfully, type help after the Ready prompt and press

Enter.

•If a list of all available commands does not appear on the screen, review the steps in this section, check the cable, or contact service personnel until the problem is solved.

•If you wish to change the default username and password for world wide web, Telnet and FTP use, continue with the section To change the default administrator password on page 17.

ATTO Technology Inc. iPBridge Installation and Operation Manual

Image 24

Contents IPBridgeTM 1500D/E IPBridgeTM 1550D/E Page Page Contents Connecting Scsi devices to the Scsi port Serial port configuration commands Mapping commands Glossary Intelligent Bridging Architecture, the engineTerm Definition Introduction Setting up the iPBridge IPBridge1500 featuresIPBridge 1550 features Possible SAN/NAS Configuration ScsiPin outs of the RJ11 connector, part number CBL-0911-001 Atto iPBridge 1500EInstallation instructions Exhibit 1.1-1 iPBridge 1500E board layoutAtto iPBridge 1500D Exhibit 1.2-1 iPBridge 1500D back panel Atto iPBridge 1550E Exhibit 1.3-1 iPBridge 1550E board layout Atto iPBridge 1550D Exhibit 1.4-1 iPBridge 1550D back panel Connecting Scsi devices to the Scsi port To connect Scsi devices to the Atto iPBridgeTo set Scsi port bus speed and transfer rates Cabling Cable typesExamples Configuring the iPBridge Connecting using the GbE portTo find the iPBridge Using Atto ExpressNAV Connecting using the serial portTo optimize ExpressNAV in Internet Explorer Select Internet OptionsUsing Telnet To connect using TelnetEnter Installation Configuration Change default username, password Scsi configurationTo change the default administrator password Managing the iPBridgeEthernet port configuration ISCSI configurationOEM configuration services MappingSerial Port Configuration ExpressNAV provides web-based interfaceStatus To open an ExpressNAV sessionBridge Configuration Advanced CLI ConfigurationTo use the Advanced Configuration Restart FirmwareGet Set Command Parameter 1 Parameter Command conventionsCLI provides ASCII-based interface Configuration & Management CLI CLI commands summary Command Defaults ExampleOEM configuration file Defaults Limits General use commands From information commands. Choices are enabled or disabled VerboseModeDiagnostic commands CLI Error Messages RouteDisplaySCSIPortList SCSITargetsMaintenance commands Configuration CLI Scsi configuration commands SpeedWrite Serial port configuration commands SerialPortBaudRateSerialPortEcho Configuration CLI Ethernet commands ReadOnlyPassword ReadOnlyUsernameISCSI commands ISNSServer MultiTargetModeMapping commands AutoMapRoute Configuration CLI Privileged OEM configuration services OEM Config file supported commands ModelNumberProductID VendorIDSingle target mode Use Command Line InterfaceMapping devices Node namesMapping single vs. multiple target mode Multiple target mode Use the ExpressNAV interfaceExample To remove an iSCSITargetUpdating firmware To use FTP over GbE to flash new firmware into the iPBridge\bridgefirmware\I1500110.ima Configuration & Management firmware update Appendix a Safety standards and compliances European Standards FC Rack Enclosures with Power Supplies PWRA-0000-FRUPower Module for Atto FC Rack SystemAtto iPBridge 2500C Atto iPBridge 1500EAccessories Cables/SCSIAppendix C Contact Atto Technology, Inc