ATTO Technology 1550D/E, 1500D/E operation manual Appendix a Safety standards and compliances

Page 58
• If necessary, consult an ATTO authorized dealer, ATTO Technical Support Staff, or an experienced radio/television technician for additional suggestions.

Appendix A Safety standards and compliances

The equipment described in this manual generates and uses radio frequency energy. If this equipment is not used in strict accordance with the manufacturer's instruction, it can and may cause interference with radio and television reception. See the Technical Specification sheet for a full list of certifications.

WARNING

Risk of explosion if battery is removed and/or replaced by an incorrect type. Dispose of used batteries in accordance with your local environmental regulations.

No operator serviceable components inside the iPBridge 1500E/D or the 1550E/D.

Do not remove cover of iPBridge 1500D or the iPBridge 1550D. Refer servicing to qualified personnel.

FCC Standards: Radio and Television Interference

WARNING

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause interference to radio communications. It has been

tested and found to comply with the limits for a Class A computing device pursuant to Subpart J of Part 15 of FCC rules, which are designed to provide a reasonable protection against such interference when operating in a commercial environment. Operation of this equipment in a residential area is likely to cause interference, in which case the user, at his own expense, will be required to take whatever measures may be required to correct the interference.

If this equipment does cause interference to radio and television reception, which can be determined by turning the equipment off and on, try to correct the interference by one or more of the following measures

• Move the receiving antenna.

• Relocate the bridge with respect to the receiver, or move the bridge away from the receiver.

• Plug the computer into a different outlet so the computer and receiver are on different branch circuits.

The booklet How to Identify and Resolve Radio/TV Interference Problems prepared by the Federal Com- munications Commission is a helpful guide. It is available from the US Government printing office, Wash- ington, DC 20402, Stock No. 004-000-00345-4.

Canadian Standards

This Class A digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.

i

ATTO Technology Inc. iPBridge Installation and Operation Manual

Page 57 Page 59
Image 58
Page 57 Page 59
Contents IPBridgeTM 1500D/E IPBridgeTM 1550D/E Page Page Contents Connecting Scsi devices to the Scsi port Serial port configuration commands Mapping commands Intelligent Bridging Architecture, the engine GlossaryTerm Definition Introduction IPBridge1500 features Setting up the iPBridgeIPBridge 1550 features Possible SAN/NAS Configuration ScsiPin outs of the RJ11 connector, part number CBL-0911-001 Atto iPBridge 1500EInstallation instructions Exhibit 1.1-1 iPBridge 1500E board layoutAtto iPBridge 1500D Exhibit 1.2-1 iPBridge 1500D back panel Atto iPBridge 1550E Exhibit 1.3-1 iPBridge 1550E board layout Atto iPBridge 1550D Exhibit 1.4-1 iPBridge 1550D back panel To connect Scsi devices to the Atto iPBridge Connecting Scsi devices to the Scsi portTo set Scsi port bus speed and transfer rates Cable types CablingExamples Connecting using the GbE port Configuring the iPBridgeTo find the iPBridge To optimize ExpressNAV in Internet Explorer Using Atto ExpressNAVConnecting using the serial port Select Internet OptionsTo connect using Telnet Using TelnetEnter Installation Configuration To change the default administrator password Change default username, passwordScsi configuration Managing the iPBridgeOEM configuration services Ethernet port configurationISCSI configuration MappingStatus Serial Port ConfigurationExpressNAV provides web-based interface To open an ExpressNAV sessionTo use the Advanced Configuration Bridge ConfigurationAdvanced CLI Configuration Restart FirmwareCommand conventions Get Set Command Parameter 1 ParameterCLI provides ASCII-based interface Configuration & Management CLI CLI commands summary Command Defaults ExampleOEM configuration file Defaults Limits General use commands From information commands. Choices are enabled or disabled VerboseModeDiagnostic commands SCSIPortList CLI Error MessagesRouteDisplay SCSITargetsMaintenance commands Configuration CLI Scsi configuration commands SpeedWrite SerialPortBaudRate Serial port configuration commandsSerialPortEcho Configuration CLI Ethernet commands ReadOnlyPassword ReadOnlyUsernameISCSI commands ISNSServer MultiTargetModeAutoMap Mapping commandsRoute Configuration CLI Privileged OEM configuration services ProductID OEM Config file supported commandsModelNumber VendorIDMapping devices Single target modeUse Command Line Interface Node namesMapping single vs. multiple target mode Multiple target mode Use the ExpressNAV interfaceExample To remove an iSCSITargetTo use FTP over GbE to flash new firmware into the iPBridge Updating firmware\bridgefirmware\I1500110.ima Configuration & Management firmware update Appendix a Safety standards and compliances European Standards Atto iPBridge 2500C FC Rack Enclosures with Power SuppliesPWRA-0000-FRUPower Module for Atto FC Rack System Atto iPBridge 1500EAccessories Cables/SCSIAppendix C Contact Atto Technology, Inc
Top Page Image Contents