ATTO Technology 1550D/E Glossary, Intelligent Bridging Architecture, the engine, Term Definition

Page 8

Introduction: iSCSI provides storage options

The iSCSI protocol allows storage devices such as hard drives, tape drives and libraries and CD jukeboxes to attach easily to Internet Protocol networks such as Gigabit Ethernet. The iPBridge 1500 and the ATTO iPBridge 1550 support the high throughput needs of streaming data transfers, optimizing performance and management using ATTO Technology intelligent Bridging Architecture™.

The iSCSI protocol increases the capabilities and performance of storage data transmission by transmitting data over local area networks (LANs), wide area networks (WANs), or the Internet, providing location-independent data storage and retrieval to enhance current and future Storage Area Networks (SANs).

Gigabit Ethernet (GbE) is a transmission technology based on the Ethernet format and protocol used in local area networks (LANs). It

provides a data rate of 1 billion bits per second (one gigabit) as defined in the IEEE 802.3 standard.

intelligent Bridging Architecture, the engine

within ATTO FibreBridge™ and iPBridge products, uses ATTO Data Routing Fabric topology and ATTO Virtual Device Manager to optimize performance. For more information see www.attotech.com/iBA.html.

Glossary

More information is available through the Storage Networking Industry Association (www.snia.org/education/dictionary), the Network Data Management Task Force (www.ndmp.org), and the IETF (www.ietf.org).

Term

Definition

Btl

Bus-Target-LUN: Identification for a parallel SCSI device

CHAP

Challenge-Handshake Authentication Protocol: If CHAP is enabled, the target

 

requires the initiator to negotiate CHAP authentication using the CHAP secrets

 

(passwords). An initiator may reject this negotiation.

DP

GbE port used for data movement and management

data port

 

firmware

Software stored in read-only memory (ROM) or programmable ROM (PROM);

 

firmware is often responsible for the behavior of a system when it is first

 

switched on

GbE

A protocol for transferring block-level IO over Telnet networks; speed at which

Gigabit Ethernet

data is passed over Ethernet

IETF

Internet Engineering Task Force: The standards body responsible for Internet

 

standards such as SNMP and Telnet through a community of network designers,

 

operators, vendors and researchers concerned with the evolution and smooth

 

operation of the Internet

initiator device

A component which originates a command

iSCSI

Internet SCSI (Small Computer System Interface), a protocol to link data storage

 

facilities over the Internet or an intranet developed by the Internet Engineering

 

Task Force (IETF); carries SCSI commands over IP networks to facilitate data

 

transfers over intranets and manage storage over long distances

LED

Light-emitting diode, a type of diode that emits light when current passes through

 

it; visible LEDs are used as indicator lights on all sorts of electronic devices

ATTO Technology Inc. iPBridge Installation and Operation Manual

Image 8
Contents IPBridgeTM 1500D/E IPBridgeTM 1550D/E Page Page Contents Connecting Scsi devices to the Scsi port Serial port configuration commands Mapping commands Term Definition GlossaryIntelligent Bridging Architecture, the engine Introduction IPBridge 1550 features Setting up the iPBridgeIPBridge1500 features Possible SAN/NAS Configuration ScsiPin outs of the RJ11 connector, part number CBL-0911-001 Atto iPBridge 1500EInstallation instructions Exhibit 1.1-1 iPBridge 1500E board layoutAtto iPBridge 1500D Exhibit 1.2-1 iPBridge 1500D back panel Atto iPBridge 1550E Exhibit 1.3-1 iPBridge 1550E board layout Atto iPBridge 1550D Exhibit 1.4-1 iPBridge 1550D back panel To set Scsi port bus speed and transfer rates Connecting Scsi devices to the Scsi portTo connect Scsi devices to the Atto iPBridge Examples CablingCable types To find the iPBridge Configuring the iPBridgeConnecting using the GbE port Using Atto ExpressNAV Connecting using the serial portTo optimize ExpressNAV in Internet Explorer Select Internet OptionsEnter Using TelnetTo connect using Telnet Installation Configuration Change default username, password Scsi configurationTo change the default administrator password Managing the iPBridgeEthernet port configuration ISCSI configurationOEM configuration services MappingSerial Port Configuration ExpressNAV provides web-based interfaceStatus To open an ExpressNAV sessionBridge Configuration Advanced CLI ConfigurationTo use the Advanced Configuration Restart FirmwareCLI provides ASCII-based interface Get Set Command Parameter 1 ParameterCommand conventions Configuration & Management CLI CLI commands summary Command Defaults ExampleOEM configuration file Defaults Limits General use commands From information commands. Choices are enabled or disabled VerboseModeDiagnostic commands CLI Error Messages RouteDisplaySCSIPortList SCSITargetsMaintenance commands Configuration CLI Scsi configuration commands SpeedWrite SerialPortEcho Serial port configuration commandsSerialPortBaudRate Configuration CLI Ethernet commands ReadOnlyPassword ReadOnlyUsernameISCSI commands ISNSServer MultiTargetModeRoute Mapping commandsAutoMap Configuration CLI Privileged OEM configuration services OEM Config file supported commands ModelNumberProductID VendorIDSingle target mode Use Command Line InterfaceMapping devices Node namesMapping single vs. multiple target mode Multiple target mode Use the ExpressNAV interfaceExample To remove an iSCSITarget\bridgefirmware\I1500110.ima Updating firmwareTo use FTP over GbE to flash new firmware into the iPBridge Configuration & Management firmware update Appendix a Safety standards and compliances European Standards FC Rack Enclosures with Power Supplies PWRA-0000-FRUPower Module for Atto FC Rack SystemAtto iPBridge 2500C Atto iPBridge 1500EAccessories Cables/SCSIAppendix C Contact Atto Technology, Inc