ATTO Technology 1550D/E, 1500D/E operation manual Atto iPBridge 1500D

Page 14

1.2 ATTO iPBridge 1500D

The ATTO iPBridge 1500D is a 1-Gigabit Ethernet to SCSI embeddable bridge for midrange performance, cost effective solutions in SMB/SME environments.

The iPBridge 1500E includes a single Ethernet port which may be used for either data transfer or configuration, a serial management port and a SCSI port.

Dimensions

Width: 7.5 inches wide

Depth: 5.0 inches long

Height: 1.76 inches

SCSI ID LED

Input voltage: 12.0V DC +10%

SCSI port

The SCSI port on the iPBridge 1500E connects storage devices into the Storage Area Network (SAN). The port is an Ultra 3 LVD/SE SCSI bus with 68-pin “P” interface: 160 MB/sec. maximum throughput, downward compatible with all forms of single-ended SCSI.

The iPBridge supports SCSI devices including hard disk drives, tape drives RAID controllers, DVD and CD libraries.

Ethernet port

The 10/100/1000 GbE RJ45 Ethernet port uses the Intel 8254x family gigabit Ethernet controllers to support Telnet-based data transfer and management through an ASCII-based command line interface or ATTO ExpressNAV, a browser-based interface.

GbE cables must be at least CAT-5E certified for 1000 Mb/sec. use.

Environment

Operating Temperature: 0-70° C external Ambient air should not exceed 40°C. Humidity: 10-90% non-condensing Recommended airflow: 11 cubic feet per minute.

Power

Plug in the 12 volt, 20 Watt wall mount adapter to the back of the unit, then into an appropriate power source (100-240 VAC input, 50/60 Hz). The power source must be connected to a protective earth ground and comply with local electrical codes. Improper grounding may result in an electrical shock or damage to the unit.

LED indicators

Activity: A green LED on the top of the iPBridge blinks to show the unit is ready and to identify the iPBridge when the CLI command IdentifyBridge is enabled. It goes dark when there is SCSI activity. SCSI Activity: the SCSI bus has an LED which is lit when the iPBridge is ready and goes dark when there is SCSI activity.

Reset switch

A manual reset switch is mounted on the board. Insert a tool in the hole in the back panel to activate the switch.

5

ATTO Technology Inc. iPBridge Installation and Operation Manual

Image 14

Contents IPBridgeTM 1500D/E IPBridgeTM 1550D/E Page Page Contents Connecting Scsi devices to the Scsi port Serial port configuration commands Mapping commands Term Definition GlossaryIntelligent Bridging Architecture, the engine Introduction IPBridge 1550 features Setting up the iPBridgeIPBridge1500 features Possible SAN/NAS Configuration ScsiPin outs of the RJ11 connector, part number CBL-0911-001 Atto iPBridge 1500EInstallation instructions Exhibit 1.1-1 iPBridge 1500E board layoutAtto iPBridge 1500D Exhibit 1.2-1 iPBridge 1500D back panel Atto iPBridge 1550E Exhibit 1.3-1 iPBridge 1550E board layout Atto iPBridge 1550D Exhibit 1.4-1 iPBridge 1550D back panel To set Scsi port bus speed and transfer rates Connecting Scsi devices to the Scsi portTo connect Scsi devices to the Atto iPBridge Examples CablingCable types To find the iPBridge Configuring the iPBridgeConnecting using the GbE port To optimize ExpressNAV in Internet Explorer Using Atto ExpressNAVConnecting using the serial port Select Internet OptionsEnter Using TelnetTo connect using Telnet Installation Configuration To change the default administrator password Change default username, passwordScsi configuration Managing the iPBridgeOEM configuration services Ethernet port configurationISCSI configuration MappingStatus Serial Port ConfigurationExpressNAV provides web-based interface To open an ExpressNAV sessionTo use the Advanced Configuration Bridge ConfigurationAdvanced CLI Configuration Restart FirmwareCLI provides ASCII-based interface Get Set Command Parameter 1 ParameterCommand conventions Configuration & Management CLI CLI commands summary Command Defaults ExampleOEM configuration file Defaults Limits General use commands From information commands. Choices are enabled or disabled VerboseModeDiagnostic commands SCSIPortList CLI Error MessagesRouteDisplay SCSITargetsMaintenance commands Configuration CLI Scsi configuration commands SpeedWrite SerialPortEcho Serial port configuration commandsSerialPortBaudRate Configuration CLI Ethernet commands ReadOnlyPassword ReadOnlyUsernameISCSI commands ISNSServer MultiTargetModeRoute Mapping commandsAutoMap Configuration CLI Privileged OEM configuration services ProductID OEM Config file supported commandsModelNumber VendorIDMapping devices Single target modeUse Command Line Interface Node namesMapping single vs. multiple target mode Multiple target mode Use the ExpressNAV interfaceExample To remove an iSCSITarget\bridgefirmware\I1500110.ima Updating firmwareTo use FTP over GbE to flash new firmware into the iPBridge Configuration & Management firmware update Appendix a Safety standards and compliances European Standards Atto iPBridge 2500C FC Rack Enclosures with Power SuppliesPWRA-0000-FRUPower Module for Atto FC Rack System Atto iPBridge 1500EAccessories Cables/SCSIAppendix C Contact Atto Technology, Inc