ATTO Technology
1500D/E, 1550D/E
operation manual
Configuration & Management firmware update
Install
Error messages
Password
Connecting using the GbE port
Maintenance
Possible SAN/NAS Configuration
Diagnostic commands
Accessories
Setting up the iPBridge
Mapping commands
Page 57
48 Configuration & Management: firmware update
Page 56
Page 58
Image 57
Page 56
Page 58
Contents
IPBridgeTM 1500D/E IPBridgeTM 1550D/E
Page
Page
Contents
Connecting Scsi devices to the Scsi port
Serial port configuration commands
Mapping commands
Glossary
Intelligent Bridging Architecture, the engine
Term Definition
Introduction
Setting up the iPBridge
IPBridge1500 features
IPBridge 1550 features
Scsi
Possible SAN/NAS Configuration
Atto iPBridge 1500E
Pin outs of the RJ11 connector, part number CBL-0911-001
Exhibit 1.1-1 iPBridge 1500E board layout
Installation instructions
Atto iPBridge 1500D
Exhibit 1.2-1 iPBridge 1500D back panel
Atto iPBridge 1550E
Exhibit 1.3-1 iPBridge 1550E board layout
Atto iPBridge 1550D
Exhibit 1.4-1 iPBridge 1550D back panel
Connecting Scsi devices to the Scsi port
To connect Scsi devices to the Atto iPBridge
To set Scsi port bus speed and transfer rates
Cabling
Cable types
Examples
Configuring the iPBridge
Connecting using the GbE port
To find the iPBridge
Connecting using the serial port
Using Atto ExpressNAV
To optimize ExpressNAV in Internet Explorer
Select Internet Options
Using Telnet
To connect using Telnet
Enter
Installation Configuration
Scsi configuration
Change default username, password
To change the default administrator password
Managing the iPBridge
ISCSI configuration
Ethernet port configuration
OEM configuration services
Mapping
ExpressNAV provides web-based interface
Serial Port Configuration
Status
To open an ExpressNAV session
Advanced CLI Configuration
Bridge Configuration
To use the Advanced Configuration
Restart Firmware
Get Set Command Parameter 1 Parameter
Command conventions
CLI provides ASCII-based interface
Configuration & Management CLI
Command Defaults Example
CLI commands summary
OEM configuration file Defaults Limits
General use commands
VerboseMode
From information commands. Choices are enabled or disabled
Diagnostic commands
RouteDisplay
CLI Error Messages
SCSIPortList
SCSITargets
Maintenance commands
Configuration CLI
Scsi configuration commands
SpeedWrite
Serial port configuration commands
SerialPortBaudRate
SerialPortEcho
Configuration CLI
Ethernet commands
ReadOnlyUsername
ReadOnlyPassword
ISCSI commands
MultiTargetMode
ISNSServer
Mapping commands
AutoMap
Route
Configuration CLI
Privileged OEM configuration services
ModelNumber
OEM Config file supported commands
ProductID
VendorID
Use Command Line Interface
Single target mode
Mapping devices
Node names
Mapping single vs. multiple target mode
Use the ExpressNAV interface
Multiple target mode
To remove an iSCSITarget
Example
Updating firmware
To use FTP over GbE to flash new firmware into the iPBridge
\bridgefirmware\I1500110.ima
Configuration & Management firmware update
Appendix a Safety standards and compliances
European Standards
PWRA-0000-FRUPower Module for Atto FC Rack System
FC Rack Enclosures with Power Supplies
Atto iPBridge 2500C
Atto iPBridge 1500E
Cables/SCSI
Accessories
Appendix C Contact Atto Technology, Inc
Related pages
All Configuration page
Interface A-1,B-4,B-8--IntLB A-1ipconfig for Q-Logic 3000
Network Configuration for Toshiba EHV Hybrid H.264 DVR
››Configurazione di un profilo VPN for Samsung GT-P7510UWDITV
Configuring Apps for Samsung SM/T530NYKAX
Routerconfig-if# ip pim nbma-mode for Cisco Systems 78-11741-02
Configure the operating system for asynchronous I/O for Sybase 15
CLI command syntax, mdadm manage RAID configuration for Emerson ATCA-S201
Restablezca la configuración de pantalla predeterminada for Samsung LH55UDCPLBB/EN
Voice Recognition & Motion Control Configuration for Samsung PN60F5500
Configuración de Ahorro energ. Plus for Samsung LS32E590CS/EN
Is the
Paulin propane heater
safe for recreational use?
Top
Page
Image
Contents