ATTO Technology 1500D/E, 1550D/E operation manual Cables/SCSI, Accessories

Page 61

SCSI cables & accessories

Cables/SCSI

CBL-VHDC-003 Cable, SCSI External, VHDCI to VHDCI, 3m.125 CBL-V68E- 03X Cable, SCSI, External, VHDCI to HD68, U320-rated, 1m 95

CBL-FP68-C3 68-pin “P” / 50-pin Centronics – 1m

CBL-FP68-C6 68-pin “P” / 50-pin Centronics – 2m

CBL-FP68-C25 68-pin “P” / 50-pin Centronics – 8m

CBL-FP68-C79 68-pin “P” / 50-pin Centronics – 24m

CBL-F68E-00X 68-pin “P” / 68-pin fine pitch “P” – 1ft

CBL-U68E-681 68-pin “P” / 68-pin fine pitch “P” – 1m

CBL-F68E-686 68-pin “P” / 68-pin fine pitch “P” – 2m

CBL-F68E-003 68-pin “P” / 68-pin fine pitch “P” – 3m

CBL-F68E-010 68-pin “P” / 68-pin fine pitch “P” – 10m

CBL-F68E-025 68-pin “P” / 68-pin fine pitch “P” – 25m

CBL-F68E-68X 68-pin “P” / 68-pin fine pitch “P” – 16m. CBL-V68E-4868-pin offset VHDCI to 68-pin VHDCI

Accessories

TERM-V68E-002 Terminator, LVD SCSI, VHDCI, Active 125

ADAP- 50AF- 68P* Adapter, SCSI, 50pin “A” Female to 68pin “P” Female 60

iv Appendix

Image 61

Contents IPBridgeTM 1500D/E IPBridgeTM 1550D/E Page Page Contents Connecting Scsi devices to the Scsi port Serial port configuration commands Mapping commands Intelligent Bridging Architecture, the engine GlossaryTerm Definition Introduction IPBridge1500 features Setting up the iPBridgeIPBridge 1550 features Scsi Possible SAN/NAS ConfigurationAtto iPBridge 1500E Pin outs of the RJ11 connector, part number CBL-0911-001Exhibit 1.1-1 iPBridge 1500E board layout Installation instructionsAtto iPBridge 1500D Exhibit 1.2-1 iPBridge 1500D back panel Atto iPBridge 1550E Exhibit 1.3-1 iPBridge 1550E board layout Atto iPBridge 1550D Exhibit 1.4-1 iPBridge 1550D back panel To connect Scsi devices to the Atto iPBridge Connecting Scsi devices to the Scsi portTo set Scsi port bus speed and transfer rates Cable types CablingExamples Connecting using the GbE port Configuring the iPBridgeTo find the iPBridge Connecting using the serial port Using Atto ExpressNAVTo optimize ExpressNAV in Internet Explorer Select Internet OptionsTo connect using Telnet Using TelnetEnter Installation Configuration Scsi configuration Change default username, passwordTo change the default administrator password Managing the iPBridgeISCSI configuration Ethernet port configurationOEM configuration services MappingExpressNAV provides web-based interface Serial Port ConfigurationStatus To open an ExpressNAV sessionAdvanced CLI Configuration Bridge ConfigurationTo use the Advanced Configuration Restart FirmwareCommand conventions Get Set Command Parameter 1 ParameterCLI provides ASCII-based interface Configuration & Management CLI Command Defaults Example CLI commands summaryOEM configuration file Defaults Limits General use commands VerboseMode From information commands. Choices are enabled or disabledDiagnostic commands RouteDisplay CLI Error MessagesSCSIPortList SCSITargetsMaintenance commands Configuration CLI Scsi configuration commands SpeedWrite SerialPortBaudRate Serial port configuration commandsSerialPortEcho Configuration CLI Ethernet commands ReadOnlyUsername ReadOnlyPasswordISCSI commands MultiTargetMode ISNSServerAutoMap Mapping commandsRoute Configuration CLI Privileged OEM configuration services ModelNumber OEM Config file supported commandsProductID VendorIDUse Command Line Interface Single target modeMapping devices Node namesMapping single vs. multiple target mode Use the ExpressNAV interface Multiple target modeTo remove an iSCSITarget ExampleTo use FTP over GbE to flash new firmware into the iPBridge Updating firmware\bridgefirmware\I1500110.ima Configuration & Management firmware update Appendix a Safety standards and compliances European Standards PWRA-0000-FRUPower Module for Atto FC Rack System FC Rack Enclosures with Power SuppliesAtto iPBridge 2500C Atto iPBridge 1500ECables/SCSI AccessoriesAppendix C Contact Atto Technology, Inc