ATTO Technology 1500D/E Bridge Configuration, Advanced CLI Configuration, Restart Firmware, Help

Page 29

iSCSI Configuration

Configurable options are

•iSCSI Alias

•iSCSI Port Number

•iSNSLoginControl

•iSNSServer

•CHAP settings: account name and secret

•CHAP direction (in, out)

See iSCSI commands on page 37 for details on each parameter.

Bridge Configuration

Configurable options are

•User name and current password

•Old Password

•New Password

•Confirm Password

•Bridge name

•Identify Bridge

•Restore Defaults

See Maintenance commands on page 29 for details on each parameter.

Mapping

While the iPBridge maps devices automatically at startup by default, you may change mapping using the ExpressNAV Mapping page. See Mapping devices on page 43 and Mapping commands on page 39 for details.

Advanced CLI Configuration

Allows you to input any CLI command available through the iPBridge.

To use the Advanced Configuration page

1Type in the CLI command

2Click the Submit button: this is equivalent to typing in the CLI command into a Telnet or serial port CLI session.

A text field beneath the box will list the most recent commands issued to the iPBridge through this page.

If you enter an incorrect parameter, the CLI help text will be displayed, showing the parameters available.

3If you are using a “set” command and the entry was correct, type saveconfiguration restart to make the changes persistent or click the Submit button to implement changes immediately.

Restart Firmware

Implements a firmware restart of the bridge and makes permanent any changes you have made since the last firmware restart.

Note

Restarting the firmware may take a few minutes.

1Click the Restart button.

A box will tell you to wait until the counter gets to 0 and then the browser will refresh.

2If the browser does not refresh after the counter gets to 0, click the link to refresh it manually.

Help

Gives help information about the command line interface commands and troubleshooting tips via links to pages with help text for each category of options and one link to the Troubleshooting Tips and FAQs page on the ATTO website,

www.attotech.com.

Contact information for ATTO technical support is on the right.

Help is always available by pressing any word shown in red on the screen.

20 Configuration & Management: ExpressNAV

Page 28 Page 30
Image 29
Page 28 Page 30
Contents IPBridgeTM 1500D/E IPBridgeTM 1550D/E Page Page Contents Connecting Scsi devices to the Scsi port Serial port configuration commands Mapping commands Term Definition GlossaryIntelligent Bridging Architecture, the engine Introduction IPBridge 1550 features Setting up the iPBridgeIPBridge1500 features Scsi Possible SAN/NAS ConfigurationAtto iPBridge 1500E Pin outs of the RJ11 connector, part number CBL-0911-001Exhibit 1.1-1 iPBridge 1500E board layout Installation instructionsAtto iPBridge 1500D Exhibit 1.2-1 iPBridge 1500D back panel Atto iPBridge 1550E Exhibit 1.3-1 iPBridge 1550E board layout Atto iPBridge 1550D Exhibit 1.4-1 iPBridge 1550D back panel To set Scsi port bus speed and transfer rates Connecting Scsi devices to the Scsi portTo connect Scsi devices to the Atto iPBridge Examples CablingCable types To find the iPBridge Configuring the iPBridgeConnecting using the GbE port Connecting using the serial port Using Atto ExpressNAVTo optimize ExpressNAV in Internet Explorer Select Internet OptionsEnter Using TelnetTo connect using Telnet Installation Configuration Scsi configuration Change default username, passwordTo change the default administrator password Managing the iPBridgeISCSI configuration Ethernet port configurationOEM configuration services MappingExpressNAV provides web-based interface Serial Port ConfigurationStatus To open an ExpressNAV sessionAdvanced CLI Configuration Bridge ConfigurationTo use the Advanced Configuration Restart FirmwareCLI provides ASCII-based interface Get Set Command Parameter 1 ParameterCommand conventions Configuration & Management CLI Command Defaults Example CLI commands summaryOEM configuration file Defaults Limits General use commands VerboseMode From information commands. Choices are enabled or disabledDiagnostic commands RouteDisplay CLI Error MessagesSCSIPortList SCSITargetsMaintenance commands Configuration CLI Scsi configuration commands SpeedWrite SerialPortEcho Serial port configuration commandsSerialPortBaudRate Configuration CLI Ethernet commands ReadOnlyUsername ReadOnlyPasswordISCSI commands MultiTargetMode ISNSServerRoute Mapping commandsAutoMap Configuration CLI Privileged OEM configuration services ModelNumber OEM Config file supported commandsProductID VendorIDUse Command Line Interface Single target modeMapping devices Node namesMapping single vs. multiple target mode Use the ExpressNAV interface Multiple target modeTo remove an iSCSITarget Example\bridgefirmware\I1500110.ima Updating firmwareTo use FTP over GbE to flash new firmware into the iPBridge Configuration & Management firmware update Appendix a Safety standards and compliances European Standards PWRA-0000-FRUPower Module for Atto FC Rack System FC Rack Enclosures with Power SuppliesAtto iPBridge 2500C Atto iPBridge 1500ECables/SCSI AccessoriesAppendix C Contact Atto Technology, Inc
Top Page Image Contents