ATTO Technology 1550D/E, 1500D/E operation manual General use commands

Page 34

2.2.2 General use commands

These CLI commands are used in a variety of situations

Help

Displays a list of available commands. If command name is specified, displays detailed command-specific information.

Immediate command: Help [command name]

Password

Specifies a password for all sessions: Telnet, FTP and ExpressNAV web-based interface. You will be prompted for the current password, to enter the new password, and to confirm the new password. Passwords are case sensitive, 0-32 characters with no spaces.An empty password can be configured by entering the Password confirmation prompts with no parameters. The command RestoreConfiguration default sets the password to its default value.

Default: Password

Set syntax: set Password

Requires a SaveConfiguration command

ReadOnlyPassword

Specifies a read only password for all sessions: Telnet, FTP and ExpressNAV web-based interface. You will be prompted for the current password, to enter the new password, and to confirm the new password. Passwords are case sensitive, 0-32 characters with no spaces.An empty password can be configured by entering the Password confirmation prompts with no parameters. The command RestoreConfiguration default sets the password to its default value.

Default: Password

Set syntax: set ReadOnlyPassword

Requires a SaveConfiguration command

ReadOnlyUsername

Specifies a read only username for all Telnet, FTP and ExpressNAV web server sessions. Username is case insensitive, 1-32 characters with no spaces.

Default: user

Set syntax: set ReadOnlyUsername [username] Requires a SaveConfiguration command

Get syntax: get Username

RestoreConfiguration

Restores configuration to either the default configuration or the configuration last saved into non-volatile memory. The saved option will undo any changes made since the last save.

Immediate command: RestoreConfiguration [Default Saved]

SaveConfiguration

Many commands require a SaveConfiguration command to be executed. This will be indicated by the return

Ready. *.

When you invoke SaveConfiguration, the current configuration is permanently saved in the iPBridge and the new configuration becomes the active configuration.

If a firmware restart is required to make the requested change permanent, you will see a prompt asking you to confirm the restart. You can override this request by indicating the override value on the command line.

You may make several changes through commands and SaveConfiguration before implementing the restart, but once you have restarted the iPBridge, all the command changes created before the restart and save will be implemented. If you select the restart option, the iPBridge will execute its complete start up cycle.

Restart or no Restart parameter is optional

Immediate command: SaveConfiguration <Restart NoRestart>

Username

Specifies a username for all Telnet, FTP and ExpressNAV web server sessions. Username is case insensitive, 1-32 characters with no spaces. You must be using the Admin password to change Username.

Default: root

Set syntax: set Username [username]

Requires entering a password

Requires a SaveConfiguration command

Get syntax: get Username

25

ATTO Technology Inc. iPBridge Installation and Operation Manual

Page 33 Page 35
Image 34
Page 33 Page 35
Contents IPBridgeTM 1500D/E IPBridgeTM 1550D/E Page Page Contents Connecting Scsi devices to the Scsi port Serial port configuration commands Mapping commands Intelligent Bridging Architecture, the engine GlossaryTerm Definition Introduction IPBridge1500 features Setting up the iPBridgeIPBridge 1550 features Possible SAN/NAS Configuration ScsiPin outs of the RJ11 connector, part number CBL-0911-001 Atto iPBridge 1500EInstallation instructions Exhibit 1.1-1 iPBridge 1500E board layoutAtto iPBridge 1500D Exhibit 1.2-1 iPBridge 1500D back panel Atto iPBridge 1550E Exhibit 1.3-1 iPBridge 1550E board layout Atto iPBridge 1550D Exhibit 1.4-1 iPBridge 1550D back panel To connect Scsi devices to the Atto iPBridge Connecting Scsi devices to the Scsi portTo set Scsi port bus speed and transfer rates Cable types CablingExamples Connecting using the GbE port Configuring the iPBridgeTo find the iPBridge To optimize ExpressNAV in Internet Explorer Using Atto ExpressNAVConnecting using the serial port Select Internet OptionsTo connect using Telnet Using TelnetEnter Installation Configuration To change the default administrator password Change default username, passwordScsi configuration Managing the iPBridgeOEM configuration services Ethernet port configurationISCSI configuration MappingStatus Serial Port ConfigurationExpressNAV provides web-based interface To open an ExpressNAV sessionTo use the Advanced Configuration Bridge ConfigurationAdvanced CLI Configuration Restart FirmwareCommand conventions Get Set Command Parameter 1 ParameterCLI provides ASCII-based interface Configuration & Management CLI CLI commands summary Command Defaults ExampleOEM configuration file Defaults Limits General use commands From information commands. Choices are enabled or disabled VerboseModeDiagnostic commands SCSIPortList CLI Error MessagesRouteDisplay SCSITargetsMaintenance commands Configuration CLI Scsi configuration commands SpeedWrite SerialPortBaudRate Serial port configuration commandsSerialPortEcho Configuration CLI Ethernet commands ReadOnlyPassword ReadOnlyUsernameISCSI commands ISNSServer MultiTargetModeAutoMap Mapping commandsRoute Configuration CLI Privileged OEM configuration services ProductID OEM Config file supported commandsModelNumber VendorIDMapping devices Single target modeUse Command Line Interface Node namesMapping single vs. multiple target mode Multiple target mode Use the ExpressNAV interfaceExample To remove an iSCSITargetTo use FTP over GbE to flash new firmware into the iPBridge Updating firmware\bridgefirmware\I1500110.ima Configuration & Management firmware update Appendix a Safety standards and compliances European Standards Atto iPBridge 2500C FC Rack Enclosures with Power SuppliesPWRA-0000-FRUPower Module for Atto FC Rack System Atto iPBridge 1500EAccessories Cables/SCSIAppendix C Contact Atto Technology, Inc
Top Page Image Contents