ATTO Technology 1550D/E, 1500D/E operation manual Contents

Page 4

Contents
Introduction: iSCSI provides storage options
Glossary
1 Setting up the iPBridge	1
iPBridge1500 features
iPBridge 1550 features
1.1 ATTO iPBridge 1500E	3
Dimensions
Environment
Power
Reset switch
SCSI port
Ethernet port
Serial port
LED indicators
Installation instructions
1.2 ATTO iPBridge 1500D	5
Dimensions
Environment
Power
SCSI port
Ethernet port
LED indicators
Reset switch
Installation instructions
1.3 ATTO iPBridge 1550E	7
Dimensions
Environment
Power
Reset switch
SCSI port
Ethernet port
Serial port
LED indicators
Installation instructions
1.4 ATTO iPBridge 1550D	9
Dimensions
Environment
Power
SCSI port
Ethernet port
LED indicators
Reset switch
Installation instructions

Image 4

Contents IPBridgeTM 1500D/E IPBridgeTM 1550D/E Page Page Contents Connecting Scsi devices to the Scsi port Serial port configuration commands Mapping commands Intelligent Bridging Architecture, the engine GlossaryTerm Definition Introduction IPBridge1500 features Setting up the iPBridgeIPBridge 1550 features Possible SAN/NAS Configuration ScsiPin outs of the RJ11 connector, part number CBL-0911-001 Atto iPBridge 1500EInstallation instructions Exhibit 1.1-1 iPBridge 1500E board layoutAtto iPBridge 1500D Exhibit 1.2-1 iPBridge 1500D back panel Atto iPBridge 1550E Exhibit 1.3-1 iPBridge 1550E board layout Atto iPBridge 1550D Exhibit 1.4-1 iPBridge 1550D back panel To connect Scsi devices to the Atto iPBridge Connecting Scsi devices to the Scsi portTo set Scsi port bus speed and transfer rates Cable types CablingExamples Connecting using the GbE port Configuring the iPBridgeTo find the iPBridge Using Atto ExpressNAV Connecting using the serial portTo optimize ExpressNAV in Internet Explorer Select Internet OptionsTo connect using Telnet Using TelnetEnter Installation Configuration Change default username, password Scsi configurationTo change the default administrator password Managing the iPBridgeEthernet port configuration ISCSI configurationOEM configuration services MappingSerial Port Configuration ExpressNAV provides web-based interfaceStatus To open an ExpressNAV sessionBridge Configuration Advanced CLI ConfigurationTo use the Advanced Configuration Restart FirmwareCommand conventions Get Set Command Parameter 1 ParameterCLI provides ASCII-based interface Configuration & Management CLI CLI commands summary Command Defaults ExampleOEM configuration file Defaults Limits General use commands From information commands. Choices are enabled or disabled VerboseModeDiagnostic commands CLI Error Messages RouteDisplaySCSIPortList SCSITargetsMaintenance commands Configuration CLI Scsi configuration commands SpeedWrite SerialPortBaudRate Serial port configuration commandsSerialPortEcho Configuration CLI Ethernet commands ReadOnlyPassword ReadOnlyUsernameISCSI commands ISNSServer MultiTargetModeAutoMap Mapping commandsRoute Configuration CLI Privileged OEM configuration services OEM Config file supported commands ModelNumberProductID VendorIDSingle target mode Use Command Line InterfaceMapping devices Node namesMapping single vs. multiple target mode Multiple target mode Use the ExpressNAV interfaceExample To remove an iSCSITargetTo use FTP over GbE to flash new firmware into the iPBridge Updating firmware\bridgefirmware\I1500110.ima Configuration & Management firmware update Appendix a Safety standards and compliances European Standards FC Rack Enclosures with Power Supplies PWRA-0000-FRUPower Module for Atto FC Rack SystemAtto iPBridge 2500C Atto iPBridge 1500EAccessories Cables/SCSIAppendix C Contact Atto Technology, Inc