ATTO Technology 1550D/E, 1500D/E operation manual Scsi configuration commands

Page 40

2.2.5 SCSI configuration commands

The SCSI ports are configured with default settings but may be customized to your specifications using the CLI commands in this section.

SCSIInitID

Specifies the SCSI initiator ID to be used on the specified SCSI port. All maps coinciding with the user-specified SCSIInitID must be set to offline and will become invalid upon issuing this command. Choices are 0 to 15.

Default: 7

Set syntax: set SCSIInitID [sb [0-15] ]

Requires a SaveConfiguration command

Get syntax: get SCSIInitID

SCSIPortBusSpeed

Controls the transfer rate at which the iPBridge will attempt to negotiate with its SCSI devices. Ultra 2 SCSI valid only if iPBridge has LVD-capable SCSI ports

Default: Ultra3

Set syntax: set SCSIPortBusSpeed [sb [fast ultra ultra2 ultra3]

Requires a SaveConfiguration command

Get syntax: get SCSIPortBusSpeed [PortNum]

SCSIPortList

Returns a list of available SCSI ports and their current status. Valid status values are O.K. and Failed.

Immediate command: SCSIPortList

SCSIPortSelTimeout

Indicates the time, in milliseconds, that the bridge waits for a response from a SCSI device on the selected port after a selection request.

Get syntax: get SCSIPortSelTimeout [sb]

SCSIPortSyncTransfer

Specifies whether synchronous SCSI transfers should be negotiated with devices on the specified SCSI port.

Default: enabled

Set syntax: set SCSIPortSyncTransfer [[sb [enabled disabled] ]

Requires a SaveConfiguration command Get syntax: get SCSIPortSyncTransfer [sb]

SCSIPortTermination

Configures/reports the SCSI internal termination of the SCSI port identified.

Default: enabled

Set syntax: set SCSIPortTermination [sb [enabled disabled]]

Requires a SaveConfiguration command Get syntax: get SCSIPortTermination [sb]

SCSIPortReset

Resets the specified SCSI bus.

Immediate command: SCSIPortReset [sb]

SCSIPortResetOnStartup

Specifies whether the SCSI port should be reset on power- up or not

Default: enabled

Set syntax: set SCSIPortResetOnStartup [sb [enabled disabled] ]

Requires a SaveConfiguration command Get syntax: get SCSIPortResetOnStartup [sb]

SCSIPortWideTransfer

Specifies whether wide SCSI transfers should be negotiated.

Default: enabled

Set syntax: set SCSIPortWideTransfer [sb [enabled disabled] ]

Requires a SaveConfiguration command Get syntax: get SCSIPortWideTransfer [sb]

SCSITargets

Returns a list of SCSI devices operational on the SCSI port.

Immediate command: SCSITargets 0

31

ATTO Technology Inc. iPBridge Installation and Operation Manual

Page 39 Page 41
Image 40
Page 39 Page 41
Contents IPBridgeTM 1500D/E IPBridgeTM 1550D/E Page Page Contents Connecting Scsi devices to the Scsi port Serial port configuration commands Mapping commands Intelligent Bridging Architecture, the engine GlossaryTerm Definition Introduction IPBridge1500 features Setting up the iPBridgeIPBridge 1550 features Possible SAN/NAS Configuration ScsiPin outs of the RJ11 connector, part number CBL-0911-001 Atto iPBridge 1500EInstallation instructions Exhibit 1.1-1 iPBridge 1500E board layoutAtto iPBridge 1500D Exhibit 1.2-1 iPBridge 1500D back panel Atto iPBridge 1550E Exhibit 1.3-1 iPBridge 1550E board layout Atto iPBridge 1550D Exhibit 1.4-1 iPBridge 1550D back panel To connect Scsi devices to the Atto iPBridge Connecting Scsi devices to the Scsi portTo set Scsi port bus speed and transfer rates Cable types CablingExamples Connecting using the GbE port Configuring the iPBridgeTo find the iPBridge Using Atto ExpressNAV Connecting using the serial portTo optimize ExpressNAV in Internet Explorer Select Internet OptionsTo connect using Telnet Using TelnetEnter Installation Configuration Change default username, password Scsi configurationTo change the default administrator password Managing the iPBridgeEthernet port configuration ISCSI configurationOEM configuration services MappingSerial Port Configuration ExpressNAV provides web-based interfaceStatus To open an ExpressNAV sessionBridge Configuration Advanced CLI ConfigurationTo use the Advanced Configuration Restart FirmwareCommand conventions Get Set Command Parameter 1 ParameterCLI provides ASCII-based interface Configuration & Management CLI CLI commands summary Command Defaults ExampleOEM configuration file Defaults Limits General use commands From information commands. Choices are enabled or disabled VerboseModeDiagnostic commands CLI Error Messages RouteDisplaySCSIPortList SCSITargetsMaintenance commands Configuration CLI Scsi configuration commands SpeedWrite SerialPortBaudRate Serial port configuration commandsSerialPortEcho Configuration CLI Ethernet commands ReadOnlyPassword ReadOnlyUsernameISCSI commands ISNSServer MultiTargetModeAutoMap Mapping commandsRoute Configuration CLI Privileged OEM configuration services OEM Config file supported commands ModelNumberProductID VendorIDSingle target mode Use Command Line InterfaceMapping devices Node namesMapping single vs. multiple target mode Multiple target mode Use the ExpressNAV interfaceExample To remove an iSCSITargetTo use FTP over GbE to flash new firmware into the iPBridge Updating firmware\bridgefirmware\I1500110.ima Configuration & Management firmware update Appendix a Safety standards and compliances European Standards FC Rack Enclosures with Power Supplies PWRA-0000-FRUPower Module for Atto FC Rack SystemAtto iPBridge 2500C Atto iPBridge 1500EAccessories Cables/SCSIAppendix C Contact Atto Technology, Inc
Top Page Image Contents