ATTO Technology 1550D/E, 1500D/E operation manual Updating firmware, bridgefirmware\I1500110.ima

Page 56

2.4 Updating firmware

Several processors control the flow of data in the ATTO iPBridge. The firmware to control these processors can easily be upgraded in the field using the PUT command from an FTP connection.

The iPBridge firmware is distributed as a compressed .zip file and can be obtained from the ATTO Technology, Inc. web site at

www.attotech.com.

To use FTP over GbE to flash new firmware into the iPBridge

1Uncompress the .zip file obtained from the ATTO Technology Inc. website

(www.attotech.com) into an image file (.ima). Note the filename.

2Establish an FTP link to the bridge that is to be flashed.

3Use the PUT command to download the firmware. For example

c:\bridge_firmware\I1500110.ima

4Once the download is complete, cycle power on the iPBridge to activate the new firmware.

47

ATTO Technology Inc. iPBridge Installation and Operation Manual

Image 56

Contents IPBridgeTM 1500D/E IPBridgeTM 1550D/E Page Page Contents Connecting Scsi devices to the Scsi port Serial port configuration commands Mapping commands Term Definition GlossaryIntelligent Bridging Architecture, the engine Introduction IPBridge 1550 features Setting up the iPBridgeIPBridge1500 features Possible SAN/NAS Configuration ScsiPin outs of the RJ11 connector, part number CBL-0911-001 Atto iPBridge 1500EInstallation instructions Exhibit 1.1-1 iPBridge 1500E board layoutAtto iPBridge 1500D Exhibit 1.2-1 iPBridge 1500D back panel Atto iPBridge 1550E Exhibit 1.3-1 iPBridge 1550E board layout Atto iPBridge 1550D Exhibit 1.4-1 iPBridge 1550D back panel To set Scsi port bus speed and transfer rates Connecting Scsi devices to the Scsi portTo connect Scsi devices to the Atto iPBridge Examples CablingCable types To find the iPBridge Configuring the iPBridgeConnecting using the GbE port Using Atto ExpressNAV Connecting using the serial portTo optimize ExpressNAV in Internet Explorer Select Internet OptionsEnter Using TelnetTo connect using Telnet Installation Configuration Change default username, password Scsi configurationTo change the default administrator password Managing the iPBridgeEthernet port configuration ISCSI configurationOEM configuration services MappingSerial Port Configuration ExpressNAV provides web-based interfaceStatus To open an ExpressNAV sessionBridge Configuration Advanced CLI ConfigurationTo use the Advanced Configuration Restart FirmwareCLI provides ASCII-based interface Get Set Command Parameter 1 ParameterCommand conventions Configuration & Management CLI CLI commands summary Command Defaults ExampleOEM configuration file Defaults Limits General use commands From information commands. Choices are enabled or disabled VerboseModeDiagnostic commands CLI Error Messages RouteDisplaySCSIPortList SCSITargetsMaintenance commands Configuration CLI Scsi configuration commands SpeedWrite SerialPortEcho Serial port configuration commandsSerialPortBaudRate Configuration CLI Ethernet commands ReadOnlyPassword ReadOnlyUsernameISCSI commands ISNSServer MultiTargetModeRoute Mapping commandsAutoMap Configuration CLI Privileged OEM configuration services OEM Config file supported commands ModelNumberProductID VendorIDSingle target mode Use Command Line InterfaceMapping devices Node namesMapping single vs. multiple target mode Multiple target mode Use the ExpressNAV interfaceExample To remove an iSCSITarget\bridgefirmware\I1500110.ima Updating firmwareTo use FTP over GbE to flash new firmware into the iPBridge Configuration & Management firmware update Appendix a Safety standards and compliances European Standards FC Rack Enclosures with Power Supplies PWRA-0000-FRUPower Module for Atto FC Rack SystemAtto iPBridge 2500C Atto iPBridge 1500EAccessories Cables/SCSIAppendix C Contact Atto Technology, Inc