ATTO Technology 1550D/E, 1500D/E operation manual Diagnostic commands

Page 36

2.2.3 Diagnostic commands

ATTO iPBridge diagnostic commands help validate iPBridge operation and diagnose/isolate iPBridge faults.

BridgeModel

Reports model information about a specific iPBridge

Get syntax: get BridgeModel

BridgeName

Specifies name used to identify individual iPBridge units. May be up to a maximum of eight characters. It is not the World Wide Name (WWN).

Set syntax: set BridgeName [value]

Requires a SaveConfiguration command

Get syntax: get BridgeName

Help

Displays a list of available commands. If command name is specified, displays detailed command-specific information.

Immediate command: Help [command name]

IdentifyBridge

Enabling this option causes the LED on the top panel of the iPBridge 1500/1550D or the activity LED on the iPBridge 1500/1550E to blink until the parameter is disabled.

Default: disabled

Set syntax: set IdentifyBridge [enableddisabled]

Get syntax: get IdentifyBridge

Info

Displays version numbers and other production information for key components within the iPBridge

Immediate command: Info

IsReserved

Displays the reservation status of the current iPBridge session/interface.

If set, the configuration image is being modified by another iPBridge services session: set commands are temporarily unavailable but information commands are available.

Executing a SaveConfiguration, RestoreConfiguration or FirmwareRestart RELEASES the iPBridge so that other services users may access it.

When iPBridge services interface is RESERVED, set commands from other users are unavailable.

At least one interface must always have access to the iPBridge.

Immediate command: IsReserved

OEMConfigFile

Reports the name of the OEM Configuration file stored in persistent memory. If no file is present, ATTO is returned. The file contains all the CLI commands that can be used to override the factory default settings of the iPBridge.

Updates may be loaded via any of the current firmware update methods.

Get syntax: get OEMConfigFile

Ping

Ping will send an ICMP echo request to the specified host.

Immediate command: ping dp0 [xxx.xxx.xxx.xxx] <count <size>>

27

ATTO Technology Inc. iPBridge Installation and Operation Manual

Image 36

Contents IPBridgeTM 1500D/E IPBridgeTM 1550D/E Page Page Contents Connecting Scsi devices to the Scsi port Serial port configuration commands Mapping commands Glossary Intelligent Bridging Architecture, the engineTerm Definition Introduction Setting up the iPBridge IPBridge1500 featuresIPBridge 1550 features Possible SAN/NAS Configuration ScsiPin outs of the RJ11 connector, part number CBL-0911-001 Atto iPBridge 1500EInstallation instructions Exhibit 1.1-1 iPBridge 1500E board layoutAtto iPBridge 1500D Exhibit 1.2-1 iPBridge 1500D back panel Atto iPBridge 1550E Exhibit 1.3-1 iPBridge 1550E board layout Atto iPBridge 1550D Exhibit 1.4-1 iPBridge 1550D back panel Connecting Scsi devices to the Scsi port To connect Scsi devices to the Atto iPBridgeTo set Scsi port bus speed and transfer rates Cabling Cable typesExamples Configuring the iPBridge Connecting using the GbE portTo find the iPBridge Using Atto ExpressNAV Connecting using the serial portTo optimize ExpressNAV in Internet Explorer Select Internet OptionsUsing Telnet To connect using TelnetEnter Installation Configuration Change default username, password Scsi configurationTo change the default administrator password Managing the iPBridgeEthernet port configuration ISCSI configurationOEM configuration services MappingSerial Port Configuration ExpressNAV provides web-based interfaceStatus To open an ExpressNAV sessionBridge Configuration Advanced CLI ConfigurationTo use the Advanced Configuration Restart FirmwareGet Set Command Parameter 1 Parameter Command conventionsCLI provides ASCII-based interface Configuration & Management CLI CLI commands summary Command Defaults ExampleOEM configuration file Defaults Limits General use commands From information commands. Choices are enabled or disabled VerboseModeDiagnostic commands CLI Error Messages RouteDisplaySCSIPortList SCSITargetsMaintenance commands Configuration CLI Scsi configuration commands SpeedWrite Serial port configuration commands SerialPortBaudRateSerialPortEcho Configuration CLI Ethernet commands ReadOnlyPassword ReadOnlyUsernameISCSI commands ISNSServer MultiTargetModeMapping commands AutoMapRoute Configuration CLI Privileged OEM configuration services OEM Config file supported commands ModelNumberProductID VendorIDSingle target mode Use Command Line InterfaceMapping devices Node namesMapping single vs. multiple target mode Multiple target mode Use the ExpressNAV interfaceExample To remove an iSCSITargetUpdating firmware To use FTP over GbE to flash new firmware into the iPBridge\bridgefirmware\I1500110.ima Configuration & Management firmware update Appendix a Safety standards and compliances European Standards FC Rack Enclosures with Power Supplies PWRA-0000-FRUPower Module for Atto FC Rack SystemAtto iPBridge 2500C Atto iPBridge 1500EAccessories Cables/SCSIAppendix C Contact Atto Technology, Inc