ATTO Technology 1550D/E, 1500D/E operation manual Atto iPBridge 1550D, Dimensions

Page 18

1.4 ATTO iPBridge 1550D

The ATTO iPBridge 1550D is a 1-Gigabit Ethernet to SCSI embeddable bridge for high performance, cost effective solutions in SMB/SME environments.

The iPBridge 1550E includes a single Ethernet port which may be used for either data transfer or configuration, a serial management port and a SCSI port.

Dimensions

Width: 7.5 inches wide

Depth: 5.0 inches long

Height: 1.76 inches

SCSI ID LED

Environment

Operating Temperature: 0-70° C external Ambient air should not exceed 40°C. Humidity: 10-90% non-condensing Recommended airflow: 11 cubic feet per minute.

Power

Plug in the 12 volt, 20 Watt wall mount adapter to the back of the unit, then into an appropriate power source (100-240 VAC input, 50/60 Hz). The power source must be connected to a protective earth ground and comply with local electrical codes. Improper grounding may result in an electrical shock or damage to the unit.

Input voltage: 12.0V DC +10%

SCSI port

The SCSI port on the iPBridge 1550E connects storage devices into the Storage Area Network (SAN). The port is an Ultra 3 LVD/SE SCSI bus with 68-pin “P” interface: 160 MB/sec. maximum throughput, downward compatible with all forms of single-ended SCSI.

The iPBridge supports SCSI devices including hard disk drives, tape drives RAID controllers, DVD and CD libraries.

Ethernet port

The 10/100/1000 GbE RJ45 Ethernet port uses the Intel 8254x family gigabit Ethernet controllers to support Telnet-based data transfer and management through an ASCII-based command line interface or ATTO ExpressNAV, a browser- based interface.

GbE cables must be at least CAT-5E certified for 1000 Mb/sec. use.

LED indicators

Activity: A green LED on the top of the iPBridge blinks to show the unit is ready and to identify the iPBridge when the CLI command IdentifyBridge is enabled. It goes dark when there is SCSI activity. SCSI Activity: the SCSI bus has an LED which is lit when the iPBridge is ready and goes dark when there is SCSI activity.

Reset switch

A manual reset switch is mounted on the board. Insert a tool in the hole in the back panel to activate the switch.

9

ATTO Technology Inc. iPBridge Installation and Operation Manual

Image 18

Contents IPBridgeTM 1500D/E IPBridgeTM 1550D/E Page Page Contents Connecting Scsi devices to the Scsi port Serial port configuration commands Mapping commands Glossary Intelligent Bridging Architecture, the engineTerm Definition Introduction Setting up the iPBridge IPBridge1500 featuresIPBridge 1550 features Possible SAN/NAS Configuration ScsiPin outs of the RJ11 connector, part number CBL-0911-001 Atto iPBridge 1500EInstallation instructions Exhibit 1.1-1 iPBridge 1500E board layoutAtto iPBridge 1500D Exhibit 1.2-1 iPBridge 1500D back panel Atto iPBridge 1550E Exhibit 1.3-1 iPBridge 1550E board layout Atto iPBridge 1550D Exhibit 1.4-1 iPBridge 1550D back panel Connecting Scsi devices to the Scsi port To connect Scsi devices to the Atto iPBridgeTo set Scsi port bus speed and transfer rates Cabling Cable typesExamples Configuring the iPBridge Connecting using the GbE portTo find the iPBridge To optimize ExpressNAV in Internet Explorer Using Atto ExpressNAVConnecting using the serial port Select Internet OptionsUsing Telnet To connect using TelnetEnter Installation Configuration To change the default administrator password Change default username, passwordScsi configuration Managing the iPBridgeOEM configuration services Ethernet port configurationISCSI configuration MappingStatus Serial Port ConfigurationExpressNAV provides web-based interface To open an ExpressNAV sessionTo use the Advanced Configuration Bridge ConfigurationAdvanced CLI Configuration Restart FirmwareGet Set Command Parameter 1 Parameter Command conventionsCLI provides ASCII-based interface Configuration & Management CLI CLI commands summary Command Defaults ExampleOEM configuration file Defaults Limits General use commands From information commands. Choices are enabled or disabled VerboseModeDiagnostic commands SCSIPortList CLI Error MessagesRouteDisplay SCSITargetsMaintenance commands Configuration CLI Scsi configuration commands SpeedWrite Serial port configuration commands SerialPortBaudRateSerialPortEcho Configuration CLI Ethernet commands ReadOnlyPassword ReadOnlyUsernameISCSI commands ISNSServer MultiTargetModeMapping commands AutoMapRoute Configuration CLI Privileged OEM configuration services ProductID OEM Config file supported commandsModelNumber VendorIDMapping devices Single target modeUse Command Line Interface Node namesMapping single vs. multiple target mode Multiple target mode Use the ExpressNAV interfaceExample To remove an iSCSITargetUpdating firmware To use FTP over GbE to flash new firmware into the iPBridge\bridgefirmware\I1500110.ima Configuration & Management firmware update Appendix a Safety standards and compliances European Standards Atto iPBridge 2500C FC Rack Enclosures with Power SuppliesPWRA-0000-FRUPower Module for Atto FC Rack System Atto iPBridge 1500EAccessories Cables/SCSIAppendix C Contact Atto Technology, Inc