ATTO Technology 1550D/E, 1500D/E operation manual Maintenance commands

Page 38

2.2.4 Maintenance commands

The CLI commands outlined in this chapter may be used to get information or perform functions which are used in a variety of situations with the ATTO iPBridge.

FirmwareRestart

Causes the iPBridge to reboot, then re-initialize its firmware.

Immediate command: FirmwareRestart

Password

RestoreConfiguration default sets the password to the default value

Passwords are case sensitive, 0-32 characters with no spaces

When the password is all 0s, Telnet and ftp do not validate the password and MD5 authentication are disabled.

Default: Password

Set syntax: set Password

Requires a SaveConfiguration command

Reserve

Reservation of the iPBridge is implicit: once the configuration image is changed by any user of services, the iPBridge becomes RESERVED. Executing a SaveConfiguration or\ Restore configuration RELEASES the iPBridge so that other services users may access it. When iPBridge services interface is RESERVED, set commands from other users are unavailable.

At least one interface must always have access to the iPBridge.

Immediate command: Reserve

RestoreConfiguration

Restores configuration to either the default configuration or the configuration last saved into non-volatile memory. The saved option will undo any changes made since the last save.

Immediate command: RestoreConfiguration [Default Saved]

SCSIPortReset

Resets the specified SCSI bus.

Immediate command: SCSIPortReset [sb]

SpeedWrite

When enabled, improves the performance of FCP WRITE commands to SCSI devices attached to the iPBridge. Specify SCSI bus (sb), target (st), LUN (sl) of a mapped SCSI device or (all) for each currently mapped device

Set syntax: set SpeedWrite SCSI [sb st sl all] [enableddisabled]

Get syntax: get SpeedWrite SCSI [sb st slall]

SpeedWriteDefault

When enabled, SpeedWrite performance enhancement is set as the default for any subsequent SCSI devices mapped manually or via an AutoMap operation. If disabled, the iPBridge will not attempt SpeedWrite performance enhancement to newly-mapped SCSI devices.

Default: disabled

Set syntax: set SpeedWriteDefault [enabled disabled]

Get syntax: get SpeedWriteDefault

Username

Specifies username for all Telnet, FTP and ExpressNAV web server sessions.The username is case insensitive, 1- 32 characters, no spaces You must have the Admin password to change Username.

Default: root

Set syntax: set Username [username]

Requires a SaveConfiguration command

Get syntax: get Username

29

ATTO Technology Inc. iPBridge Installation and Operation Manual

Page 37 Page 39
Image 38
Page 37 Page 39
Contents IPBridgeTM 1500D/E IPBridgeTM 1550D/E Page Page Contents Connecting Scsi devices to the Scsi port Serial port configuration commands Mapping commands Term Definition GlossaryIntelligent Bridging Architecture, the engine Introduction IPBridge 1550 features Setting up the iPBridgeIPBridge1500 features Possible SAN/NAS Configuration ScsiPin outs of the RJ11 connector, part number CBL-0911-001 Atto iPBridge 1500EInstallation instructions Exhibit 1.1-1 iPBridge 1500E board layoutAtto iPBridge 1500D Exhibit 1.2-1 iPBridge 1500D back panel Atto iPBridge 1550E Exhibit 1.3-1 iPBridge 1550E board layout Atto iPBridge 1550D Exhibit 1.4-1 iPBridge 1550D back panel To set Scsi port bus speed and transfer rates Connecting Scsi devices to the Scsi portTo connect Scsi devices to the Atto iPBridge Examples CablingCable types To find the iPBridge Configuring the iPBridgeConnecting using the GbE port To optimize ExpressNAV in Internet Explorer Using Atto ExpressNAVConnecting using the serial port Select Internet OptionsEnter Using TelnetTo connect using Telnet Installation Configuration To change the default administrator password Change default username, passwordScsi configuration Managing the iPBridgeOEM configuration services Ethernet port configurationISCSI configuration MappingStatus Serial Port ConfigurationExpressNAV provides web-based interface To open an ExpressNAV sessionTo use the Advanced Configuration Bridge ConfigurationAdvanced CLI Configuration Restart FirmwareCLI provides ASCII-based interface Get Set Command Parameter 1 ParameterCommand conventions Configuration & Management CLI CLI commands summary Command Defaults ExampleOEM configuration file Defaults Limits General use commands From information commands. Choices are enabled or disabled VerboseModeDiagnostic commands SCSIPortList CLI Error MessagesRouteDisplay SCSITargetsMaintenance commands Configuration CLI Scsi configuration commands SpeedWrite SerialPortEcho Serial port configuration commandsSerialPortBaudRate Configuration CLI Ethernet commands ReadOnlyPassword ReadOnlyUsernameISCSI commands ISNSServer MultiTargetModeRoute Mapping commandsAutoMap Configuration CLI Privileged OEM configuration services ProductID OEM Config file supported commandsModelNumber VendorIDMapping devices Single target modeUse Command Line Interface Node namesMapping single vs. multiple target mode Multiple target mode Use the ExpressNAV interfaceExample To remove an iSCSITarget\bridgefirmware\I1500110.ima Updating firmwareTo use FTP over GbE to flash new firmware into the iPBridge Configuration & Management firmware update Appendix a Safety standards and compliances European Standards Atto iPBridge 2500C FC Rack Enclosures with Power SuppliesPWRA-0000-FRUPower Module for Atto FC Rack System Atto iPBridge 1500EAccessories Cables/SCSIAppendix C Contact Atto Technology, Inc
Top Page Image Contents