Schneider Electric 890USE19600 Version 1.0 manual Auto-Configuration, About Auto

Page 32

Configuring the Island Bus

Auto-Configuration

Introduction

All Advantys STB I/O modules are shipped with a set of predefined parameters that

 

allow an island to be operational as soon as it is initialized. This ability of island

 

modules to operate with default parameters is known as auto-configuration. Once

 

an island bus has been installed, you can begin using it as a node on that network.

About Auto-

 

Auto-configuration occurs when:

Configuration

￿You power up an island for the first time.

 

You push the RST button.

 

As part of the auto-configuration process, the NIM checks each module and

 

confirms that it has been properly connected to the island bus. The NIM stores the

 

default operating parameters for each module in Flash memory.

 

 

32

890USE19600 April 2004

Image 32
Contents Advantys STB 890USE19600 VersionPage Table of Contents Application Example Important Information Safety InformationProcedure Safety Information About the Book At a GlanceValidity Note Construed as a commitment by Schneider ElectricAbout the Book Topic IntroductionSummary What’s in this Chapter? What Is Advantys STB? IntroductionIsland Bus I/O BasicWhat Is a Network Interface Module? Structural Components of a simplified Interbus network are shown below About InterbusOutputs in 4 ms Physical Layer TopologyNode AddressingInput and output data in the masters buffer On the shift register ring on which data is circulatedIntroduction Product specifications of the basic Interbus NIM STB NIB Basic NIM ModuleWhat’s in this Chapter?External Features of the STB NIB 1010 NIM Features Called out in the illustration belowFeature Function HardwareSpace reserved for the network connectors NIM housing STB NIB 1010 Fieldbus Interface SummaryFieldbus Port ConnectionsConnectors InterbusNetworking CableLED Physical Description OverviewGeneral IndicationsNIM Activity LEDsPower Supply Interface Island is the two-receptacle connector illustrated belowPhysical DescriptionUse either RightLogic Power Improper Galvanic IsolationCharacteristics Power SupplyRequirements ExternalSTB NIB 1010 Module Specifications Technical SpecificationsConfiguring the Island Bus Basic island configuration Auto-AddressingAbout the Island Bus AddressAn Example Module Physical Location Island Bus AddressAbout Auto Auto-ConfigurationConfiguration Been successfully configured at least once RST ButtonHinged cover StageIsland Fallback Scenarios FallbackScenarios HeartbeatFieldbus Communications Support Introduction What’s in this Chapter?Interbus ID Code LowHigh Bytes Data TypeData Length Data Exchange Data and StatusObjects ObjectsInternal Process ImageWord BoundariesOutput Data Input DataExchange Contains the NIM statusApplication Example With an Advantys STB NIB 1010 basic NIMSample Island Assembly AssemblyFieldbus network Sample IslandI/O modules have the following island bus addresses Model Module Type Island Bus AddressNetwork Configuration Considerations For use with an Advantys STB islandConnection Devices on an Interbus networkBefore You BeginSyCon ConsiderationsUsing SyCon to Configure an STB Island on Interbus With SyConStage Description Step Action CommentTo add the NIM to the network configuration ConfiguringAdd the NIM WorkspaceCreate an EDS InstructionsSaving CMD Using CMD to Configure an STB Island on InterbusIsland slave to your configuration using CMD Add AddingIsland Slave DownloadingApplication Example Glossary ARP BOSCan COBComs CRCDhcp DINEDS EIAEMC EMIEOS FedpFsdp GSDBase ScanningIEC IEC type 1 inputIndustrial I/O Input filteringInput polarity Input responseEnergized and open when the coil is energized Energized and closed when the coil is energizedContact NemaNIM NMTPLC PDMPDO Process I/O ProducerConsumer model Profibus DPRTD SAPScada SDOSmmps SnmpTFE StdpTCP UDP VaristorSuppress transient voltage surges Voltage groupIndex Heartbeat message, 34 housing ID code InterbusIndex