Schneider Electric INTERBUS Basic Network Interface Module manual RST Button, Hinged cover, Stage

Page 33

Configuring the Island Bus

The RST Button

Summary	Use the RST function to reconfigure your island after you have added a new I/O
	module to a previously auto-configured island. If a new I/O module is added to the
	island, pressing the RST button forces the auto-configuration process. The updated
	island configuration data is automatically saved. RST works only after the island has
	been successfully configured at least once.
Physical
Physical	The RST button is located immediately above the CFG port, and behind the same
Description	hinged cover:

RST button

Holding down the RST button for two seconds or longer causes the island to auto configure and the Flash memory to be overwritten.

Engaging the To engage the RST button, use a small screwdriver with a flat blade no wider than

RST Button 2.5 mm (.10 in). Do not use a sharp object that might damage the RST button or a soft item such as a pencil that might break off and jam the button.

When you push the RST button for at least two seconds, the NIM reconfigures the island bus as follows:

Stage

Description

1The NIM auto-addresses the I/O modules on the island and derives their factory-default configuration values.

2The NIM overwrites the current configuration in Flash memory with configuration data that uses the factory-default values for the I/O modules.

3It re-initializes the island bus and brings it into operational mode.

Note: Network settings such as the fieldbus baud and the fieldbus node ID remain unaffected.

890USE19600 April 2004

33

Image 33

Contents 890USE19600 Version Advantys STBPage Table of Contents Application Example Safety Information ProcedureImportant Information Safety Information At a Glance About the BookValidity Note Construed as a commitment by Schneider ElectricAbout the Book Introduction Summary What’s in this Chapter?Topic Introduction What Is Advantys STB?Island Bus I/O BasicWhat Is a Network Interface Module? Structural About Interbus Outputs in 4 msComponents of a simplified Interbus network are shown below Topology Physical LayerAddressing NodeInput and output data in the masters buffer On the shift register ring on which data is circulatedIntroduction STB NIB Basic NIM Module Product specifications of the basic Interbus NIMWhat’s in this Chapter?Features Called out in the illustration below External Features of the STB NIB 1010 NIMFeature Function HardwareSpace reserved for the network connectors NIM housing Summary STB NIB 1010 Fieldbus InterfaceFieldbus Port ConnectionsInterbus ConnectorsNetworking CableOverview LED Physical DescriptionGeneral IndicationsLEDs NIM ActivityIsland is the two-receptacle connector illustrated below Power Supply InterfacePhysical DescriptionRight Use eitherImproper Galvanic Isolation Logic PowerPower Supply CharacteristicsRequirements ExternalTechnical Specifications STB NIB 1010 Module SpecificationsConfiguring the Island Bus Auto-Addressing Basic island configurationAbout the Island Bus AddressModule Physical Location Island Bus Address An ExampleAuto-Configuration ConfigurationAbout Auto RST Button Been successfully configured at least onceHinged cover StageFallback Island Fallback ScenariosScenarios HeartbeatIntroduction What’s in this Chapter? Fieldbus Communications SupportLow Interbus ID CodeHigh Bytes Data TypeData Length Data and Status Data ExchangeObjects ObjectsProcess Image InternalWord BoundariesInput Data Output DataExchange Contains the NIM statusWith an Advantys STB NIB 1010 basic NIM Application ExampleAssembly Sample Island AssemblyFieldbus network Sample IslandModel Module Type Island Bus Address I/O modules have the following island bus addressesFor use with an Advantys STB island Network Configuration ConsiderationsConnection Devices on an Interbus networkBegin Before YouSyCon ConsiderationsWith SyCon Using SyCon to Configure an STB Island on InterbusStage Description Step Action CommentConfiguring To add the NIM to the network configurationAdd the NIM WorkspaceInstructions Create an EDSSaving Using CMD to Configure an STB Island on Interbus Island slave to your configuration using CMDCMD Adding AddIsland Slave DownloadingApplication Example Glossary BOS ARPCOB CanComs CRCDIN DhcpEDS EIAEMI EMCEOS FedpGSD FsdpScanning BaseIEC IEC type 1 inputInput filtering Industrial I/OInput polarity Input responseEnergized and closed when the coil is energized Energized and open when the coil is energizedContact NemaNMT NIMPDM PDOPLC Producer Process I/OConsumer model Profibus DPSAP RTDScada SDOSnmp SmmpsStdp TCPTFE Varistor UDPSuppress transient voltage surges Voltage groupIndex Interbus Heartbeat message, 34 housing ID codeIndex