Schneider Electric INTERBUS Basic Network Interface Module manual Before You, Begin, SyCon, Cmd

Page 45

 

Application Example

 

 

Before You

Before attempting to use the application examples in this chapter, make sure:

Begin

your Advantys STB modules are assembled, installed, and powered according to

 

￿your particular system, application, and network requirements

 

you know the input and output process data lengths for your specific configuration

 

(the sample island assembly’s input length is 80 bits and the output length is 64

 

bits)

 

You should have a working familiarity with both the INTERBUS fieldbus protocol and

 

your configuration software, either SyCon or CMD.

 

 

 

Note: For specific information about your configuration software, consult the

 

manufacturer’s documentation included with the Hilscher (SyCon) or Phoenix

 

Contact (CMD) product.

SyCon

 

 

You should have the EDS file and corresponding bitmap files that were supplied with

Considerations

the STB NIB 1010 INTERBUS NIM (also available at www.schneiderauto-

 

mation.com), or you have created an EDS that is specific to the sample island

 

assembly with the Advantys or SyCon configuration software.

CMD

 

You should have the Schneider device database, Schneider_Device_DB, available

Considerations

at www.schneiderautomation.com. It includes the Advantys STB catalog entry. If

 

you don’t have this database, you can create a configuration-specific device by

 

following the instructions for CMD configuration.

 

The sample island assembly’s input length is 80 bits and the output length is 64 bits.

 

If you do not account for the entire data length of your island, process data will be

 

truncated or connection to the network will be impossible.

 

 

890USE19600 April 2004

45

Image 45
Contents 890USE19600 Version Advantys STBPage Table of Contents Application Example Safety Information ProcedureImportant Information Safety Information At a Glance About the BookValidity Note Construed as a commitment by Schneider ElectricAbout the Book Introduction Summary What’s in this Chapter?Topic Introduction What Is Advantys STB?Island Bus I/O BasicWhat Is a Network Interface Module? Structural About Interbus Outputs in 4 msComponents of a simplified Interbus network are shown below Topology Physical LayerAddressing NodeInput and output data in the masters buffer On the shift register ring on which data is circulatedIntroduction STB NIB Basic NIM Module Product specifications of the basic Interbus NIMWhat’s in this Chapter?Features Called out in the illustration below External Features of the STB NIB 1010 NIMFeature Function HardwareSpace reserved for the network connectors NIM housing Summary STB NIB 1010 Fieldbus InterfaceFieldbus Port ConnectionsInterbus ConnectorsNetworking CableOverview LED Physical DescriptionGeneral IndicationsLEDs NIM ActivityIsland is the two-receptacle connector illustrated below Power Supply InterfacePhysical DescriptionRight Use eitherImproper Galvanic Isolation Logic PowerPower Supply CharacteristicsRequirements ExternalTechnical Specifications STB NIB 1010 Module SpecificationsConfiguring the Island Bus Auto-Addressing Basic island configurationAbout the Island Bus AddressModule Physical Location Island Bus Address An ExampleAuto-Configuration ConfigurationAbout Auto RST Button Been successfully configured at least onceHinged cover StageFallback Island Fallback ScenariosScenarios HeartbeatIntroduction What’s in this Chapter? Fieldbus Communications SupportLow Interbus ID CodeHigh Bytes Data TypeData Length Data and Status Data ExchangeObjects ObjectsProcess Image InternalWord BoundariesInput Data Output DataExchange Contains the NIM statusWith an Advantys STB NIB 1010 basic NIM Application ExampleAssembly Sample Island AssemblyFieldbus network Sample IslandModel Module Type Island Bus Address I/O modules have the following island bus addressesFor use with an Advantys STB island Network Configuration ConsiderationsConnection Devices on an Interbus networkBegin Before YouSyCon ConsiderationsWith SyCon Using SyCon to Configure an STB Island on InterbusStage Description Step Action CommentConfiguring To add the NIM to the network configurationAdd the NIM WorkspaceInstructions Create an EDSSaving Using CMD to Configure an STB Island on Interbus Island slave to your configuration using CMDCMD Adding AddIsland Slave DownloadingApplication Example Glossary BOS ARPCOB CanComs CRCDIN DhcpEDS EIAEMI EMCEOS FedpGSD FsdpScanning BaseIEC IEC type 1 inputInput filtering Industrial I/OInput polarity Input responseEnergized and closed when the coil is energized Energized and open when the coil is energizedContact NemaNMT NIMPDM PDOPLC Producer Process I/OConsumer model Profibus DPSAP RTDScada SDOSnmp SmmpsStdp TCPTFE Varistor UDPSuppress transient voltage surges Voltage groupIndex Interbus Heartbeat message, 34 housing ID codeIndex