Schneider Electric INTERBUS Basic Network Interface Module manual Interbus, Networking, Cable

Page 21

The STB NIB 1010 Basic NIM Module

The pin-out for both the in (upper) and out (lower) connectors should be according to the table below (pin numbers correspond to callouts in the figure above):

Pin

Signal (in)

Signal (out)

 

 

 

1

DO1

DO2

 

 

 

2

DI1

DI2

 

 

 

3

GND1

GND

 

 

 

4

unused

unused

 

 

 

5

unused

+5 V

 

 

 

6

/DO1

/DO2

 

 

 

7

/DI1

/DI2

 

 

 

8

unused

unused

 

 

 

9

unused

RBST (see note below)

 

 

 

 

Note: The RBST pin detects the presence of a subsequent node on the ring. In the

 

absence of this detection (or if the node has no out connector at all), the network

 

ring is closed.

INTERBUS

 

 

The drop cable from the fieldbus to the Advantys STB INTERBUS NIM (and the one

Networking

from the NIM to the next INTERBUS node) must have connectors that observe this

Cable and

pin assignment scheme. INTERBUS networking cables are shielded, twisted-pair

Connectors

electrical cables, compliant with INTERBUS standard DR-303-1. There should not

 

be an interruption to any wire in bus cables. This allows for a future specification for

 

use of reserved pins.

 

 

890USE19600 April 2004

21

Image 21
Contents 890USE19600 Version Advantys STBPage Table of Contents Application Example Safety Information ProcedureImportant Information Safety Information At a Glance About the BookValidity Note Construed as a commitment by Schneider ElectricAbout the Book Introduction Summary What’s in this Chapter?Topic Introduction What Is Advantys STB?Island Bus I/O BasicWhat Is a Network Interface Module? Structural About Interbus Outputs in 4 msComponents of a simplified Interbus network are shown below Topology Physical LayerAddressing NodeInput and output data in the masters buffer On the shift register ring on which data is circulatedIntroduction STB NIB Basic NIM Module Product specifications of the basic Interbus NIMWhat’s in this Chapter?Features Called out in the illustration below External Features of the STB NIB 1010 NIMFeature Function HardwareSpace reserved for the network connectors NIM housing Summary STB NIB 1010 Fieldbus InterfaceFieldbus Port ConnectionsInterbus ConnectorsNetworking CableOverview LED Physical DescriptionGeneral IndicationsLEDs NIM ActivityIsland is the two-receptacle connector illustrated below Power Supply InterfacePhysical DescriptionRight Use eitherImproper Galvanic Isolation Logic PowerPower Supply CharacteristicsRequirements ExternalTechnical Specifications STB NIB 1010 Module SpecificationsConfiguring the Island Bus Auto-Addressing Basic island configurationAbout the Island Bus AddressModule Physical Location Island Bus Address An ExampleAuto-Configuration ConfigurationAbout Auto RST Button Been successfully configured at least onceHinged cover StageFallback Island Fallback ScenariosScenarios HeartbeatIntroduction What’s in this Chapter? Fieldbus Communications SupportLow Interbus ID CodeHigh Bytes Data TypeData Length Data and Status Data ExchangeObjects ObjectsProcess Image InternalWord BoundariesInput Data Output DataExchange Contains the NIM statusWith an Advantys STB NIB 1010 basic NIM Application ExampleAssembly Sample Island AssemblyFieldbus network Sample IslandModel Module Type Island Bus Address I/O modules have the following island bus addressesFor use with an Advantys STB island Network Configuration ConsiderationsConnection Devices on an Interbus networkBegin Before YouSyCon ConsiderationsWith SyCon Using SyCon to Configure an STB Island on InterbusStage Description Step Action CommentConfiguring To add the NIM to the network configurationAdd the NIM WorkspaceInstructions Create an EDSSaving Using CMD to Configure an STB Island on Interbus Island slave to your configuration using CMDCMD Adding AddIsland Slave DownloadingApplication Example Glossary BOS ARPCOB CanComs CRCDIN DhcpEDS EIAEMI EMCEOS FedpGSD FsdpScanning BaseIEC IEC type 1 inputInput filtering Industrial I/OInput polarity Input responseEnergized and closed when the coil is energized Energized and open when the coil is energizedContact NemaNMT NIMPDM PDOPLC Producer Process I/OConsumer model Profibus DPSAP RTDScada SDOSnmp SmmpsStdp TCPTFE Varistor UDPSuppress transient voltage surges Voltage groupIndex Interbus Heartbeat message, 34 housing ID codeIndex