Schneider Electric 890USE19600 Version 1.0 Using CMD to Configure an STB Island on Interbus, Cmd

Page 50

Application Example

Using CMD to Configure an STB Island on INTERBUS

Introduction	Use these directions to add an Advantys STB island slave to your INTERBUS
	network using Phoenix Contact’s CMD software. The employed master device is a
	controller board that you select. In this example, we will use a PC with an IBS/4K
	controller board. The stages of this process are described in the following table:

	Stage	Description

	1	Add the controller board

	2	Add the island slave

	3	Save and download the configuration
The CMD

	In this configuration example, you will add a master device and an Advantys STB
Workspace	island slave to your configuration using CMD.
	The CMD workspace should resemble the following figure after you’ve added the

controller board and INTERBUS NIM slave to your network configuration with the following instructions:

50	890USE19600 April 2004

Image 50

Contents Advantys STB 890USE19600 VersionPage Table of Contents Application Example Important Information Safety InformationProcedure Safety Information Validity Note About the BookAt a Glance Construed as a commitment by Schneider ElectricAbout the Book Topic IntroductionSummary What’s in this Chapter? Island Bus I/O What Is Advantys STB?Introduction BasicWhat Is a Network Interface Module? Structural Components of a simplified Interbus network are shown below About InterbusOutputs in 4 ms Physical Layer TopologyInput and output data in the masters buffer NodeAddressing On the shift register ring on which data is circulatedIntroduction What’s in this Product specifications of the basic Interbus NIMSTB NIB Basic NIM Module Chapter?Feature Function External Features of the STB NIB 1010 NIMFeatures Called out in the illustration below HardwareSpace reserved for the network connectors NIM housing Fieldbus Port STB NIB 1010 Fieldbus InterfaceSummary ConnectionsNetworking ConnectorsInterbus CableGeneral LED Physical DescriptionOverview IndicationsNIM Activity LEDsPhysical Power Supply InterfaceIsland is the two-receptacle connector illustrated below DescriptionUse either RightLogic Power Improper Galvanic IsolationRequirements CharacteristicsPower Supply ExternalSTB NIB 1010 Module Specifications Technical SpecificationsConfiguring the Island Bus About the Island Basic island configurationAuto-Addressing Bus AddressAn Example Module Physical Location Island Bus AddressAbout Auto Auto-ConfigurationConfiguration Hinged cover Been successfully configured at least onceRST Button StageScenarios Island Fallback ScenariosFallback HeartbeatFieldbus Communications Support Introduction What’s in this Chapter?High Bytes Interbus ID CodeLow Data TypeData Length Objects Data ExchangeData and Status ObjectsWord InternalProcess Image BoundariesExchange Output DataInput Data Contains the NIM statusApplication Example With an Advantys STB NIB 1010 basic NIMFieldbus network Sample Island AssemblyAssembly Sample IslandI/O modules have the following island bus addresses Model Module Type Island Bus AddressConnection Network Configuration ConsiderationsFor use with an Advantys STB island Devices on an Interbus networkSyCon Before YouBegin ConsiderationsStage Description Using SyCon to Configure an STB Island on InterbusWith SyCon Step Action CommentAdd the NIM To add the NIM to the network configurationConfiguring WorkspaceCreate an EDS InstructionsSaving CMD Using CMD to Configure an STB Island on InterbusIsland slave to your configuration using CMD Island Slave AddAdding DownloadingApplication Example Glossary ARP BOSComs CanCOB CRCEDS DhcpDIN EIAEOS EMCEMI FedpFsdp GSDIEC BaseScanning IEC type 1 inputInput polarity Industrial I/OInput filtering Input responseContact Energized and open when the coil is energizedEnergized and closed when the coil is energized NemaNIM NMTPLC PDMPDO Consumer model Process I/OProducer Profibus DPScada RTDSAP SDOSmmps SnmpTFE StdpTCP Suppress transient voltage surges UDPVaristor Voltage groupIndex Heartbeat message, 34 housing ID code InterbusIndex

Using CMD to Configure an STB Island on INTERBUS

Introduction

Stage

The CMD

Workspace

island slave to your configuration using CMD.