Schneider Electric 66124 Installation in the UPS, Sensor installation option, Led, Act, Ups

Page 14

Ethernet port

LED

Colour

Activity

Description

 

 

 

 

 

 

 

 

 

 

ACT

Green

Off

Card not connected to the network.

 

 

On

Card

connected to

the

network

but

 

 

 

without activity

 

 

 

 

 

 

 

 

 

 

 

 

 

Flashing

Port

is

active

in

receiving

/

 

 

 

transmission

 

 

 

 

 

 

 

 

 

 

 

100M

Orange

Off

Port operating at 10Mbits/s.

 

 

 

On

Port operating at 100Mbits/s.

 

Service port (Settings/Sensor)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

LED

Colour

Activity

Description

 

 

 

 

UPS

Green

Off

Card startup in progress.

 

Data

 

On

Communication with UPS in progress

 

 

 

 

Normal operation.

 

 

 

 

 

Flashing

 

Communication with the UPS is

 

 

 

 

 

 

operational

 

 

 

RS232

Orange

Off

Configuration menu is active

 

 

 

On

Normal

operation.

Configuration

 

 

 

 

 

menu is deactived

 

 

 

 

 

Flashing

Communication with the Environment

 

 

 

 

 

Sensor (option).

 

 

 

3.3Installation in the UPS

The Network Management Card (66123) can be "hot" installed in the MGE Galaxy 7000 UPS or SSC unit.

Note the card's MAC address prior to insertion

Connect the ETHERNET cable

Insert and tighten the card's retaining screws

Wait 3 min.; the card is completely operational when the green UPS Data LED flashes continuously

3.4Sensor installation (option)

The Environment sensor is available as an option on the Network Management Card. SKU number is 66846.

The sensor allows remote monitoring of the UPS's environment through regular measurements: temperature, humidity, status of two external contacts. It also enables notification of alarms (e-mail, trap SNMP) according to pre-programmed thresholds.

It is connected to the Service port (Settings/Sensor) directly on the Network Management Card with a standard Ethernet cable (20 meters maximum).

Recognition is automatic. Supervision and configuration are performed via a menu that can be accessed directly from the home page.

Network Management Card & Modbus/Jbus

34022321XT indice :AE

Page 14/98

Network Management Teleservice Card

 

 

APC by Schneider Electric

www.apc.com

Image 14
Contents Page Contents Notification Installation MGE MIBMGE Galaxy 7000 Network Management card presentation Connecting the UPS to the Ethernet network Protection of the computers / serversSupervision of the UPSs over the network Sending text messages SMS Teleservice for NmtcDirect sending of E-mail Environment Sensor optionConfiguration Technical dataHardware characteristics EMC CompatibilityEnvironment sensor AdministrationNetwork MIB Management Information BaseModbus/Jbus for Inmc Mgeups Default parametersBOOTP/DHCP 1UPS/NMTC+ 9 UPS/INMCIndications Installation Network Management Card & Modbus/Jbus InmcUnpacking and check on contents LED Installation in the UPSSensor installation option ACTInstallation Network Management Teleservice Card Nmtc Installation in the UPS Line Phone Port Nmtc Inmc ConfigurationConfigure IP parameters Your network is equipped with a Dhcp server Test after configuration Your network is not equipped with a Dhcp serverUPS Supervision and administration by browserOptimising the performance of your browser UPS propertiesUPS zone general information on the UPS Page Page Page Power Saving Mode representation Efficiency Booster Mode UPS measurements UPS status zone Essential information Viewing the alarms Viewing the About your UPS window On-line help Shutdown parameters Shutdonw criteria are describe below Measurements Event log Click on Event Log in the menuSystem log Click on System log. in the menuNotification Email NotificationPage Mail Message Settings SenderConfiguration Network settings Page System Notified Applications Page Central shutdown configuration TLSRSAWITH512MD5 Access controlTLS Page Date and time Firmware upload Characteristics Environment Status Environment Settings Page 4 Log Server protection Set-up of the shutdown parametersShutdown criteria managed by the Network Management Card Shutdown when backup time is less than Shutdown durationGeneral overview TeleserviceTeleservice procedure Page Configuration via RS232 Choice 1 Restart / ResetChoice 2 Modify Network settings Choice 2 Network ConfigurationChoice 1 Read Network settings MGE UPS Systems Network Management Card Choice 3 Lost password / Set Login Password to DefaultChoice 3 Set Ethernet speed Choice 4 Return to Default Configuration 10.1.1 RS232 link configuration and connection Modbus/Jbus installation & useInstallation 10.1.2 RS485 link configuration and connection 10.1.2.1 RS485 connectionPage 10.1.2.2 RS485 link configuration for 2 wires connexion Page 10.1.2.3 RS485 link configuration for 4 wires connexion Page Configuration of the JBUS/MODBUS communication parameters Choice 3 Display Jbus diagnostics Choice 1 Display Jbus settingsChoice 2 Modify Jbus settings Choice 4 Reset Jbus diagnosticsChoice 5 Return to Jbus Default Configuration Choice 6 Display Jbus framesAdditional Web pages Modbus register map Detailled status tableINMC/NMTC SSCMeasurement table Environnement Sensor .3.3.1 Sensor Status table Sensor Measurements tableSensor customisation table RO Examples of Modbus register map Global overviewUPS on AC Normal input Main UPS statusUPS on Battery Word + Bit Main UPS statusLow Battery Warning UPS on Bypass due to End of battery runtime UPS on Bypass due to manual order UPS on Manual Bypass UPS running Power Saving Mode Communication lost Modbus Status Address Value Word + Bit Main UPS statusAppendices Tables of alarms and eventsTable of alarms and UPS events UPS OK Table of system alarms Snmp objects MGE MIBPage Page Table des Traps MIB TrapMIB Management Information Base GlossaryIsxc Network Management ProxyNSM Network Shutdown Module RebootNMS Network Management Station Snmp RFC