Schneider Electric 66123, 66124 user manual Notification

Page 3

 

6.2.1.1

"UPS" zone: general information on the UPS

22

 

6.2.1.2

Power Saving Mode representation (Efficiency Booster Mode)

26

 

6.2.1.3

"UPS measurements”

27

 

6.2.1.4

"UPS status" zone: Essential information

28

 

6.2.1.5

Viewing the alarms

29

 

6.2.1.6

Viewing the “About your UPS” window

30

 

6.2.2

On-line help

31

 

6.2.3

Shutdown parameters

32

 

6.2.4

Measurements

34

 

6.2.5

Event log

35

 

6.2.6

System log

36

 

6.3

NOTIFICATION

37

 

6.3.1

Email Notification

37

 

6.3.2

E-mail Message Settings

39

 

6.4

CONFIGURATION

40

 

6.4.1

Network settings

41

 

6.4.2

System

43

 

6.4.3

Notified Applications

44

 

6.4.4

Central shutdown configuration

46

 

6.4.5

Access control

47

 

6.4.6

Date and time

49

 

6.4.7

Firmware upload

50

 

6.5

ENVIRONMENT SENSOR (OPTION)

51

 

6.5.1

Characteristics

51

 

6.5.2

Environment Status

52

 

6.5.3

Environment Settings

53

 

6.5.4

Log

..................................................................................................................................................................................................

55

7

SERVER PROTECTION

56

 

7.1

SET-UP OF THE SHUTDOWN PARAMETERS

56

 

7.2

SHUTDOWN CRITERIA MANAGED BY THE NETWORK MANAGEMENT CARD

57

 

7.2.1 Backup time before initiating the shutdown procedure (Shutdown After - Shutdown Timer)

57

 

7.2.2 Initiating the shutdown procedure when the battery autonomy ratio is lower than: (If remaining time ratio under)

58

 

7.2.3 Shutdown when backup time is less than

58

 

7.2.4

Shutdown duration

58

8

TELESERVICE

59

 

8.1.1

Teleservice procedure

59

 

8.1.2

General overview

59

9

CONFIGURATION VIA RS232

61

 

9.1

CHOICE 1: RESTART / RESET

61

 

9.2

CHOICE 2: NETWORK CONFIGURATION

62

 

9.2.1 Choice 1: Read Network settings

62

 

9.2.2 Choice 2: Modify Network settings

62

 

9.2.3 Choice 3: Set Ethernet speed

63

 

9.3

CHOICE 3: LOST PASSWORD / SET LOGIN PASSWORD TO DEFAULT

63

 

9.4

CHOICE 4: RETURN TO DEFAULT CONFIGURATION

64

Network Management Card & Modbus/Jbus

34022321XT indice :AE

Page 3/98

Network Management Teleservice Card

 

 

APC by Schneider Electric

 

 

www.apc.com

 

 

Image 3
Contents Page Contents Notification MGE MIB InstallationMGE Galaxy 7000 Network Management card presentation Protection of the computers / servers Connecting the UPS to the Ethernet networkSupervision of the UPSs over the network Environment Sensor option Teleservice for NmtcDirect sending of E-mail Sending text messages SMSEMC Compatibility Technical dataHardware characteristics ConfigurationMIB Management Information Base AdministrationNetwork Environment sensorModbus/Jbus for Inmc 1UPS/NMTC+ 9 UPS/INMC Default parametersBOOTP/DHCP MgeupsInstallation Network Management Card & Modbus/Jbus Inmc Unpacking and check on contentsIndications ACT Installation in the UPSSensor installation option LEDInstallation Network Management Teleservice Card Nmtc Installation in the UPS Line Phone Port Configuration Configure IP parametersNmtc Inmc Your network is equipped with a Dhcp server Your network is not equipped with a Dhcp server Test after configurationUPS properties Supervision and administration by browserOptimising the performance of your browser UPSUPS zone general information on the UPS Page Page Page Power Saving Mode representation Efficiency Booster Mode UPS measurements UPS status zone Essential information Viewing the alarms Viewing the About your UPS window On-line help Shutdown parameters Shutdonw criteria are describe below Measurements Click on Event Log in the menu Event logClick on System log. in the menu System logEmail Notification NotificationPage Sender Mail Message SettingsConfiguration Network settings Page System Notified Applications Page Central shutdown configuration Access control TLSTLSRSAWITH512MD5 Page Date and time Firmware upload Characteristics Environment Status Environment Settings Page 4 Log Set-up of the shutdown parameters Server protectionShutdown criteria managed by the Network Management Card Shutdown duration Shutdown when backup time is less thanTeleservice Teleservice procedureGeneral overview Page Choice 1 Restart / Reset Configuration via RS232Choice 2 Network Configuration Choice 1 Read Network settingsChoice 2 Modify Network settings Choice 3 Lost password / Set Login Password to Default Choice 3 Set Ethernet speedMGE UPS Systems Network Management Card Choice 4 Return to Default Configuration Modbus/Jbus installation & use Installation10.1.1 RS232 link configuration and connection 10.1.2.1 RS485 connection 10.1.2 RS485 link configuration and connectionPage 10.1.2.2 RS485 link configuration for 2 wires connexion Page 10.1.2.3 RS485 link configuration for 4 wires connexion Page Configuration of the JBUS/MODBUS communication parameters Choice 4 Reset Jbus diagnostics Choice 1 Display Jbus settingsChoice 2 Modify Jbus settings Choice 3 Display Jbus diagnosticsChoice 6 Display Jbus frames Choice 5 Return to Jbus Default ConfigurationAdditional Web pages Detailled status table Modbus register mapSSC INMC/NMTCMeasurement table Sensor Measurements table Environnement Sensor .3.3.1 Sensor Status tableSensor customisation table RO Global overview Examples of Modbus register mapMain UPS status UPS on AC Normal inputWord + Bit Main UPS status UPS on BatteryLow Battery Warning UPS on Bypass due to End of battery runtime UPS on Bypass due to manual order UPS on Manual Bypass UPS running Power Saving Mode Modbus Status Address Value Word + Bit Main UPS status Communication lostTables of alarms and events Table of alarms and UPS eventsAppendices UPS OK Table of system alarms MGE MIB Snmp objectsPage Page MIB Trap Table des TrapsNetwork Management Proxy GlossaryIsxc MIB Management Information BaseRFC RebootNMS Network Management Station Snmp NSM Network Shutdown Module