Schneider Electric 66124, 66123 user manual Your network is not equipped with a Dhcp server

Page 20

5.1.2 Your network is not equipped with a DHCP server

In the main menu enter 2, then 2 again. The menu is displayed:

Follow the instructions and enter the static IP parameters.

At the end of the menu, wait for the "Done" message to be displayed indicating that the IP parameters have been saved.

-----------------------------------------------------------------------------

Network settings

-----------------------------------------------------------------------------

1 : Read Network settings

2 : Modify Network settings

3 : Set Ethernet speed

0 : Exit

-----------------------------------------------------------------------------

For each of the following questions, you can press <Return> to select the value shown in braces, or you can enter a new value.

Should this target obtain IP settings from the network?[N] N

Static IP address [172.17.21.94]? 172.17.21.21

Static IP address is 172.17.21.21

Subnet Mask IP address [255.255.248.0]? 255.255.255.0

Subnet Mask IP address is 255.255.255.0

Gateway address IP address [172.17.17.1]? 172.17.17.1

Gateway address IP address is 172.17.17.1

Wait during your new configuration is saved ...

Reset the card to take into account the new configuration.

Return to the main menu and enter 1 then 2.

The card restarts with the new IP parameters.

5.2Test after configuration

To check that the Network Management Card is operational after installation and configuration.

From a station connected to the same subnet as the card, open a web browser and enter the IP address of the card in the address field.

Network Management Card & Modbus/Jbus

34022321XT indice :AE

Page 20/98

Network Management Teleservice Card

 

 

APC by Schneider Electric

www.apc.com

Image 20
Contents Page Contents Notification Installation MGE MIBMGE Galaxy 7000 Network Management card presentation Connecting the UPS to the Ethernet network Protection of the computers / serversSupervision of the UPSs over the network Teleservice for Nmtc Direct sending of E-mailSending text messages SMS Environment Sensor optionTechnical data Hardware characteristicsConfiguration EMC CompatibilityAdministration NetworkEnvironment sensor MIB Management Information BaseModbus/Jbus for Inmc Default parameters BOOTP/DHCPMgeups 1UPS/NMTC+ 9 UPS/INMCIndications Installation Network Management Card & Modbus/Jbus InmcUnpacking and check on contents Installation in the UPS Sensor installation optionLED ACTInstallation Network Management Teleservice Card Nmtc Installation in the UPS Line Phone Port Nmtc Inmc ConfigurationConfigure IP parameters Your network is equipped with a Dhcp server Test after configuration Your network is not equipped with a Dhcp serverSupervision and administration by browser Optimising the performance of your browserUPS UPS propertiesUPS zone general information on the UPS Page Page Page Power Saving Mode representation Efficiency Booster Mode UPS measurements UPS status zone Essential information Viewing the alarms Viewing the About your UPS window On-line help Shutdown parameters Shutdonw criteria are describe below Measurements Event log Click on Event Log in the menuSystem log Click on System log. in the menuNotification Email NotificationPage Mail Message Settings SenderConfiguration Network settings Page System Notified Applications Page Central shutdown configuration TLSRSAWITH512MD5 Access controlTLS Page Date and time Firmware upload Characteristics Environment Status Environment Settings Page 4 Log Server protection Set-up of the shutdown parametersShutdown criteria managed by the Network Management Card Shutdown when backup time is less than Shutdown durationGeneral overview TeleserviceTeleservice procedure Page Configuration via RS232 Choice 1 Restart / ResetChoice 2 Modify Network settings Choice 2 Network ConfigurationChoice 1 Read Network settings MGE UPS Systems Network Management Card Choice 3 Lost password / Set Login Password to DefaultChoice 3 Set Ethernet speed Choice 4 Return to Default Configuration 10.1.1 RS232 link configuration and connection Modbus/Jbus installation & useInstallation 10.1.2 RS485 link configuration and connection 10.1.2.1 RS485 connectionPage 10.1.2.2 RS485 link configuration for 2 wires connexion Page 10.1.2.3 RS485 link configuration for 4 wires connexion Page Configuration of the JBUS/MODBUS communication parameters Choice 1 Display Jbus settings Choice 2 Modify Jbus settingsChoice 3 Display Jbus diagnostics Choice 4 Reset Jbus diagnosticsChoice 5 Return to Jbus Default Configuration Choice 6 Display Jbus framesAdditional Web pages Modbus register map Detailled status tableINMC/NMTC SSCMeasurement table Environnement Sensor .3.3.1 Sensor Status table Sensor Measurements tableSensor customisation table RO Examples of Modbus register map Global overviewUPS on AC Normal input Main UPS statusUPS on Battery Word + Bit Main UPS statusLow Battery Warning UPS on Bypass due to End of battery runtime UPS on Bypass due to manual order UPS on Manual Bypass UPS running Power Saving Mode Communication lost Modbus Status Address Value Word + Bit Main UPS statusAppendices Tables of alarms and eventsTable of alarms and UPS events UPS OK Table of system alarms Snmp objects MGE MIBPage Page Table des Traps MIB TrapGlossary IsxcMIB Management Information Base Network Management ProxyReboot NMS Network Management Station SnmpNSM Network Shutdown Module RFC