Texas Instruments TMS320C6455 manual Deac Command

Page 18

Peripheral Architecture

www.ti.com

The DEAC command closes a single bank of memory specified by the bank select signals. Figure 7 shows the timings diagram for a DEAC command.

Figure 7. DEAC Command

DDR2CLKOUT

DEAC

DDR2CLKOUT

DSDCKE

DCE0

DSDRAS

DSDCAS

DSDWE

DEA[13:11,9:0]

DEA[10]

DBA[2:0]

DSDDQM[3:0]

18	C6455/C6454 DDR2 Memory Controller	SPRU970G – December 2005 – Revised June 2011
		Submit Documentation Feedback

Copyright © 2005–2011, Texas Instruments Incorporated

Image 18

Contents Users Guide Submit Documentation Feedback Contents List of Figures List of Tables Submit Documentation Feedback Read This First Read This First Features Functional Block DiagramPurpose of the Peripheral Industry Standards Compliance Statement Signal Descriptions Clock ControlMemory Map DDR2 Memory Controller Signal Descriptions Pin DescriptionCommand Function DDR2 Sdram CommandsTruth Table for DDR2 Sdram Commands Protocol DescriptionsMode Register Set MRS and Emrs DDR2 MRS and Emrs CommandRefresh Mode Refresh CommandActv Command Activation ActvDcab Command Deactivation Dcab and DeacDeac Command Read Command DDR2 Read CommandAddressable Memory Ranges Write WRT CommandMemory Width, Byte Alignment, and Endianness Address Type Generated by DDR2Bit Field Bit Value Bit Description Bank Configuration Register Fields for Address MappingAddress Mapping IbankLogical Address-to-DDR2 Sdram Address Map for 32-Bit Sdram Logical Address-to-DDR2 Sdram Address Map DDR2 Memory Controller Interface DDR2 Memory Controller Fifo DescriptionDDR2 Memory Controller Fifo Block Diagram Command Ordering and Scheduling, Advanced ConceptCommand Starvation Refresh Urgency Levels Refresh SchedulingPossible Race Condition Urgency Level DescriptionDevice and DDR2 Memory Controller Reset Relationship Self-Refresh ModeReset Considerations DDR2 Memory Controller Reset Effect Initiated byDDR2 Sdram Extended Mode Register 1 Configuration 11.1 DDR2 Sdram Device Mode Register Configuration ValuesDDR2 Sdram Mode Register Configuration Mode Register FieldInterrupt Support 11.2 DDR2 Sdram Initialization After Reset11.3 DDR2 Sdram Initialization After Register Configuration Edma Event SupportUsing the DDR2 Memory Controller Connecting the DDR2 Memory Controller to DDR2 SdramConnecting to Two 16-Bit DDR2 Sdram Devices Connecting to a Single 16-Bit DDR2 Sdram Device Connecting to Two 8-Bit DDR2 Sdram Devices Programming the Sdram Refresh Control Register Sdrfc Programming the Sdram Configuration Register SdcfgSdcfg Configuration FieldConfiguring Sdram Timing Registers SDTIM1 and SDTIM2 DDR2 Memory Refresh SpecificationSdrfc Configuration SDTIM1 ConfigurationDDR2 Sdram Data Register Field Sheet Parameter SDTIM2 ConfigurationDmcctl Configuration Name DescriptionDDR2 Memory Controller Registers OffsetRegister Description Module ID and Revision Register Midr Module ID and Revision Register Midr Field DescriptionsBit Field Value Description DDR2 Memory Controller Status Register Dmcstat IfrdySdram Configuration Register Sdcfg Sdram Configuration Register Sdcfg Field DescriptionsSequence. Values 4-7 are reserved for this field Sdram Refresh Control Register Sdrfc Sdram Refresh Control Register Sdrfc Field DescriptionsTrfc TRP Trcd TWR Sdram Timing 1 Register SDTIM1Sdram Timing 1 Register SDTIM1 Field Descriptions Tras TRC TrrdUsing this formula Todt Txsnr Sdram Timing 2 Register SDTIM2Sdram Timing 2 Register SDTIM2 Field Descriptions Txsrd Trtp TckeBurst Priority Register Bprio Burst Priority Register Bprio Field DescriptionsPrioraise DDR2 Memory Controller Control Register Dmcctl DDR2 Memory Controller Control Register DmcctlRevision History Rfid Products ApplicationsDSP TI E2E Community Home