Texas Instruments TMS320C6455 manual Deactivation Dcab and Deac, Dcab Command

Page 17

www.ti.com

Peripheral Architecture

2.4.4Deactivation (DCAB and DEAC)

The precharge all banks command (DCAB) is performed after a reset to the DDR2 memory controller or following the initialization sequence. DDR2 SDRAMs also require this cycle prior to a refresh (REFR) and mode set register commands (MRS and EMRS). During a DCAB command, DEA10 is driven high to ensure the deactivation of all banks. Figure 6 shows the timing diagram for a DCAB command.

Figure 6. DCAB Command

DDR2CLKOUT

DCAB

DDR2CLKOUT

DSDCKE

DCE0

DSDRAS

DSDCAS

DSDWE

DEA[13:11,9:0]

DEA[10]

DBA[2:0]

DSDDQM[3:0]

SPRU970G – December 2005 – Revised June 2011	C6455/C6454 DDR2 Memory Controller	17
Submit Documentation Feedback

Copyright © 2005–2011, Texas Instruments Incorporated

Image 17

Contents Users Guide Submit Documentation Feedback Contents List of Figures List of Tables Submit Documentation Feedback Read This First Read This First Purpose of the Peripheral FeaturesFunctional Block Diagram Industry Standards Compliance Statement Memory Map Signal DescriptionsClock Control Pin Description DDR2 Memory Controller Signal DescriptionsTruth Table for DDR2 Sdram Commands DDR2 Sdram CommandsCommand Function Protocol DescriptionsDDR2 MRS and Emrs Command Mode Register Set MRS and EmrsRefresh Command Refresh ModeActivation Actv Actv CommandDeactivation Dcab and Deac Dcab CommandDeac Command DDR2 Read Command Read CommandMemory Width, Byte Alignment, and Endianness Write WRT CommandAddressable Memory Ranges Address Type Generated by DDR2Address Mapping Bank Configuration Register Fields for Address MappingBit Field Bit Value Bit Description IbankLogical Address-to-DDR2 Sdram Address Map for 32-Bit Sdram Logical Address-to-DDR2 Sdram Address Map DDR2 Memory Controller Fifo Description DDR2 Memory Controller InterfaceCommand Ordering and Scheduling, Advanced Concept DDR2 Memory Controller Fifo Block DiagramCommand Starvation Possible Race Condition Refresh SchedulingRefresh Urgency Levels Urgency Level DescriptionReset Considerations Self-Refresh ModeDevice and DDR2 Memory Controller Reset Relationship DDR2 Memory Controller Reset Effect Initiated byDDR2 Sdram Mode Register Configuration 11.1 DDR2 Sdram Device Mode Register Configuration ValuesDDR2 Sdram Extended Mode Register 1 Configuration Mode Register Field11.3 DDR2 Sdram Initialization After Register Configuration 11.2 DDR2 Sdram Initialization After ResetInterrupt Support Edma Event SupportConnecting the DDR2 Memory Controller to DDR2 Sdram Using the DDR2 Memory ControllerConnecting to Two 16-Bit DDR2 Sdram Devices Connecting to a Single 16-Bit DDR2 Sdram Device Connecting to Two 8-Bit DDR2 Sdram Devices Sdcfg Configuration Programming the Sdram Configuration Register SdcfgProgramming the Sdram Refresh Control Register Sdrfc FieldSdrfc Configuration DDR2 Memory Refresh SpecificationConfiguring Sdram Timing Registers SDTIM1 and SDTIM2 SDTIM1 ConfigurationDmcctl Configuration SDTIM2 ConfigurationDDR2 Sdram Data Register Field Sheet Parameter Name DescriptionRegister Description DDR2 Memory Controller RegistersOffset Bit Field Value Description Module ID and Revision Register MidrModule ID and Revision Register Midr Field Descriptions Ifrdy DDR2 Memory Controller Status Register DmcstatSdram Configuration Register Sdcfg Field Descriptions Sdram Configuration Register SdcfgSequence. Values 4-7 are reserved for this field Sdram Refresh Control Register Sdrfc Field Descriptions Sdram Refresh Control Register SdrfcSdram Timing 1 Register SDTIM1 Field Descriptions Sdram Timing 1 Register SDTIM1Trfc TRP Trcd TWR Tras TRC TrrdUsing this formula Sdram Timing 2 Register SDTIM2 Field Descriptions Sdram Timing 2 Register SDTIM2Todt Txsnr Txsrd Trtp TckePrioraise Burst Priority Register BprioBurst Priority Register Bprio Field Descriptions DDR2 Memory Controller Control Register Dmcctl DDR2 Memory Controller Control Register DmcctlRevision History DSP Products ApplicationsRfid TI E2E Community Home