Sharp MX-M160D, MX-M200D operation manual Warranty, EMC this machine and peripheral devices

Each instruction also covers the optional units used with these products.

In some areas, the "POWER" switch positions are marked "I" and " " on the copier instead of "ON" and "OFF".

The symbol " " denotes the copier is not completely de-energized but in a stand-by condition at this "POWER" switch position.

If your copier is so marked, please read "I" for "ON" and " " for "OFF".

Caution!

For complete electrical disconnection, pull out the main plug.

The socket-outlet shall be installed near the equipment and shall be easily accessible.

➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣	➣➢➣➢➣➢➣➢➣ ➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢		➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣
		The equipment should be installed near an accessible socket outlet for easy disconnection.

		Notice for users in the UK
		MAINS PLUG WIRING INSTRUCTIONS
	The mains lead of this equipment is already fitted with a mains plug which is either a non-rewireable
	(moulded) or a rewireable type. Should the fuse need to be replaced, a BSI or ASTA approved fuse
	to BS1362 marked	or		and of the same rating as the one removed from the plug must
	be used.
	Always refit the fuse cover after replacing the fuse on the moulded plug. Never use the plug without
	the fuse cover fitted.
	In the unlikely event of the socket outlet in your home not being compatible with the plug supplied
	either cut-off the moulded plug (if this type is fitted) or remove by undoing the screws if a rewireable
	plug is fitted and fit an appropriate type observing the wiring code below.
	DANGER: The fuse should be removed from the cut-off plug and the plug destroyed immediately
	and disposed of in a safe manner. Under no circumstances should the cut-off plug be inserted
	elsewhere into a 13A socket outlet as a serious electric shock may occur.
	To fit an appropriate plug to the mains lead, follow the instructions below:
	IMPORTANT: The wires in this mains lead are coloured in accordance with the following code:
			GREEN-AND-YELLOW: Earth
			BLUE:		Neutral
			BROWN:		Live
	As the colours of the wires in this mains lead may not correspond with coloured markings
	identifying the terminals in your plug, proceed as follows:
	The wire which is coloured GREEN-AND-YELLOWmust be connected to the terminal in the plug
	which is marked with the letter E, or by the safety earth symbol					, or coloured green or green-
	and-yellow.
	The wire which is coloured BLUE must be connected to the terminal which is marked with the letter
	N or coloured black.
	The wire which is coloured BROWN must be connected to the terminal which is marked with the
	letter L or coloured red.
	If you have any doubt, consult a qualified electrician.
	WARNING: THIS APPARATUS MUST BE EARTHED.
➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢

Shielded interface cables must be used with this equipment to maintain compliance with EMC regulations.

EMC (this machine and peripheral devices)

Warning:

This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.

Warranty

While every effort has been made to make this document as accurate and helpful as possible, SHARP Corporation makes no warranty of any kind with regard to its content. All information included herein is subject to change without notice. SHARP is not responsible for any loss or damages, direct or indirect, arising from or related to the use of this operation manual.

© Copyright SHARP Corporation 2009. All rights reserved. Reproduction, adaptation or translation without prior written permission is prohibited, except as allowed under copyright laws.