Sharp MX-M200D, MX-M160D operation manual Energy Save, Auto Power SHUT-OFF Timer, Preheat Mode

Page 87

SYSTEM SETTINGS GUIDE

To enable the setting, select "DISABLE PAPER SIZE SET" and press the [OK] key so that a checkmark appears in the checkbox.

To disable the setting, select "DISABLE PAPER SIZE SET" once again and press the [OK] key so that the checkmark is cleared from the checkbox.

ENERGY SAVE

These programs are used to configure energy saving settings. To access one of these programs, select "ENERGY SAVE" in the mode selection screen, and select the desired program in the energy save screen, and then press the [OK] key.

Select "AUTO POWER SHUT-OFF TIMER" and press the [OK] key. The following screen will appear.

AUTO POWER OFF

min. (1~240)

1

Select the desired time with the [ ] or [ ]

 

key.

2

Press the [OK] key.

AUTO POWER SHUT-OFF

This program is used to enable auto power shut-off mode, which automatically turns off the power to the fusing unit if the operation panel is not used for a certain duration of time.

Enabling auto power shut-off mode helps conserve energy, preserve natural resources, and reduce environmental pollution.

The function is initially enabled.

Rather than disabling the auto power Note shut-off feature, it is recommended that you

first try lengthening the time set in "AUTO POWER SHUT-OFF TIMER" (see below). In most cases a suitable timer setting will allow work to proceed with minimal delay and still enable you to enjoy the benefits of power conservation.

To enable auto power shut-off mode, select "AUTO POWER SHUT-OFF", and press the [OK] key so that a checkmark appears in the checkbox.

To disable auto power shut-off mode, select "AUTO POWER SHUT-OFF" once again and press the [OK] key so that the checkmark is cleared from the checkbox.

AUTO POWER SHUT-OFF TIMER

This program is used to set the duration of time until auto power shut-off mode activates when the operation panel is not used. Using this function helps conserve energy, preserve natural resources, and reduce environmental pollution.

"1 min.", "5 min.", "30 min.", "60 min.", "120 min." or "240 min." can be selected for the duration of time. Select a setting that suits your work conditions.

PREHEAT MODE

This program is used to set the duration of time until preheat mode, which automatically lowers the fusing unit temperature, activates when the operation panel is not used. Using this function helps conserve energy, preserve natural resources, and reduce environmental pollution. "1 min.", "5 min.", "30 min.", "60 min.", "120 min.", or "240 min." can be selected for the duration of time. Select a setting that suits your work conditions.

Select "PREHEAT MODE" and press the [OK] key. The following screen will appear.

PREHEAT MODE

 

 

 

min.

 

 

(1~240)

 

1

Select the desired time with the [ ] or [ ]

 

 

key.

 

2

Press the [OK] key.

7

 

 

 

 

 

 

85

Page 86 Page 88
Image 87
Page 86 Page 88
Contents Part 2 Copier Operation Part 1 General InformationEMC this machine and peripheral devices WarrantyPart 1 General Information Trademark acknowledgments Product Configurations 250-sheet paper feed unit AR-D35MX-M200D Contents A Copy Erase copy XY zoom copyingRotation copy Margin shiftFollow the cautions below when using this machine For Europe Laser InformationEnvironmental Information Installation RequirementsConventions used in this manual Software setup guideManuals Provided with the Product Meaning of R in original and paper size indicationsMain Features Fax function option Network connection optionEnvironment and people friendly design Part Names and Functions Side cover handle Document cover when installedFusing unit paper guide Open to remove misfed paper Side coverOperation Panel Auto Image key Start key / indicatorPaper Select key Copy Ratio keyIcons appearing in the special function icon display Example Copy modeOperation in COPY, PRINT, SCAN, and FAX Modes Display base screenPower save modes Turning the Power on and OFFPower on Power OFFPaper that can be used for automatic 2-sided printing Default settingsLoading Paper PaperLoading Paper Special paperLoading paper in a tray Envelopes Open the bypass traySET Changing the Paper Size Setting of a TraySET A4R ModesDisabling Enabling Auto Tray Switching Auto Tray SwitchingPaper Size SET When the copy job is finished, press the ACC.#-C key Auditing ModeNumber of Accounts in Auditing Mode Using Auditing ModeTroubleshooting and Maintenance MACHINE/COPYING Problems TroubleshootingPaper misfeed Too much paper is loaded in the tray Selected paper sizePaper misfeed has occurred Paper is not loaded properlyOriginal is smaller than A5 5-1/2 x 8-1/2 size Original is curled or foldedOriginal has many solid black areas Original size is not Automatically selected orIndicators and Display Messages Message ActionMB of expansion memory Section a Removing MisfeedsOriginal Misfeed in the SPF Remove the misfed originalSection C Misfeed in the Bypass TrayClose the front cover and the side cover Misfeed in the MachineMisfeed in a Open the front coverMisfeed in B Misfeed in C Misfeed in Tray250-sheet paper feed unit AR-D35 Open the side cover Gently push tray 2 into the machineRemove the misfed paper Gently close the side coverClose the front cover Replacing the Toner CartridgeAn A3 or 11 x 17 page is counted as two pages Checking the Total Output CountCleaning the Machine Cleaning the Document Glass SPF/DOCUMENT CoverCleaning the Bypass Tray Paper Feed Roller Position Cleaning the Transfer ChargerAdjusting the Display Contrast Adjust the contrast with the or keySelect Display Contrast with the or key Optional Equipment Specifications Reversing Single Pass Feeder / Single Pass FeederSheet Paper Feed Unit / 2 X 250-SHEET Paper Feed Unit Store paper in the wrapper and lying flat Storage of SuppliesProper Storage Store the supplies in a location that isPart 2 Copier Operation Page Make sure that the desired paper tray is selected Normal CopyingCopying from the document glass Close the SPFCopy will be delivered to Stream feeding modeCopying from the SPF Press the Start key to begin copyingOriginals that can be used in the SPF Auto paper select modeRemoving the document cover Copying books or originals with folds or creasesText Making a Copy Darker or LighterAuto Text/photoSelecting the Tray Setting the Number of CopiesAuto tray switching Important note when making a large number of copiesSelect ORIG. Size Enter from the menu with the or key Selecting the Original SizeORIG. Size Enter Inch ORIG. Size EnterExtra EnterExtra OKORIG. Size EnterPress the Auto Image key Reducing or Enlarging a CopyAutomatic Ratio Selection Press the Paper Select key to select the desired trayKey Increase the ratio in increments of 1% Key Select a larger preset ratioKey Select a smaller preset ratio Key Decrease the ratio in increments of 1%XY Zoom OkadjustXY Zoom Special FunctionVertical ratio can now be selected AdjustOFF Set the vertical ratio with the , , , or keysOne-sided original → Two sides TWO-SIDED CopyingTWO-SIDED Copying Original → PaperMode TWO-SIDED Copying of ONE-SIDED OriginalsCopy Binding Change OFFCopy Mode Binding Change on Select 2 to 2 with the or key, or with the 2-SIDED Copy key Set the number of copies and press Start keyTo stop copying in the middle Select 2 to 1 with the or key, or with the 2-SIDED Copy key Copy ModeOriginal TWO-SIDED Copies Using the Bypass TrayPlace original B as shown below Vertically-orientedCheckmark appears Dual page CopySpecial OkoffInterrupting a Copy RUN Press the Interrupt keyReplace the previous originals and press the Start key Sort No sort Sort ModeRotating the Image 90 Degrees Copies of multiple original pages can collated into setsPress the Output key Offset function enabled Offset function disabledSort No Sort1 copy layouts Press the Paper Select key to select the desired paper trayBorder PatternAN Okadjust Edge Erasing Shadows around Edges of a CopyErase DualSelect the erasure width with the or key Card Shot Card ShotModes Card ShotFront side of the card is scanned 25%, 50%, 64%, 77%, 95%, 100%, 121%, 129%, 141%, 200%, 400% SpecificationsCopies/min A4R 8-1/2 x 11R Copies/min 2 x 11R A4, B5, A5 8-1/2 xAppendix Output tray specificationsPurpose of the System Settings Programs for Copy ModeProgramming AN Administrator Password Change Admin PW Programming AN Administrator PasswordProgram name System Settings ListUsing the System Settings SettingsCopier Account Control Auditing ModeReset Account Reset 1 ACCACC. # Control ACC. # ControlDelete Change ACC. # Security Cancel Jobs of Invalid AccountsAccount Limit Single ACC. LimitOffset Function Waiting Copy Lamp SettingUSB2.0 Mode Device ControlOperation Setting Keys Touch Sound AT Initial Point Disable Auto KEY RepeatDisable Paper Size SET KEY Touch SoundEnergy Save Auto Power SHUT-OFFAuto Power SHUT-OFF Timer Preheat ModeCopy Settings Default Exposure Rotation Copy Stream FeedingSort Auto Select Disable 2-SIDED Copy Resolution in AUTO/TEXT ModePhoto Mode Default Disable Auto Paper SelectionMaterial Safety Data Sheet Exposure Controls / Personal Protection Physical and Chemical Properties Ecological Information Supplier Identification Hazards Identification Physical and Chemical Properties No data are available Index Symbols / Numbers13, 31 TroubleshootingNormal copying Reducing or enlarging a copyTwo-sided copies of two-sided originals TroubleshootingConvenient copy functions Copying, starting100 Administrator Password Number Factory Setting 102 103 Other Countries outside the EU Sonninstraße 3, D-20097 Hamburg Sharp Electronics Europe GmbHMX-M160D/MX-M200D
Top Page Image Contents