Sharp MX-M160D, MX-M200D operation manual Copy Settings

Page 88

SYSTEM SETTINGS GUIDE

COPY SETTINGS

These programs are used to enable various copy functions. To access one of these programs, select "COPIER" in the mode selection screen, select the desired program in the copy settings screen, and press the [OK] key.

EXPOSURE ADJUST

This program is used to adjust the exposure level when "AUTO" is used for the exposure mode. The auto exposure level can be set separately for the document glass and the SPF.

One of five levels can be selected, with the left end of the scale the lightest level and the right end of the scale the darkest level.

The factory default setting is the middle level.

Select "EXPOSURE ADJUST" and press the [OK] key. The following screen will appear.

EXPOSURE ADJUST

PLATEN

SPF/RSPF

1 Select "PLATEN" or "SPF/RSPF" with the [ ] or [ ] key.

2 Press the [] or [] key to adjust the exposure.

3 Repeat steps 1 and 2 to adjust the other exposure.

4 Press the [OK] key.

MARGIN DEFAULT

(When the dual function board is installed)

This is used to set the default margin width. The factory default setting is "10 mm (1/2 inch)".

Select "MARGIN DEFAULT" and press the [OK] key. The following screen will appear.

MARGIN DEFAULT

mm (0~20)

1 Adjust the default margin width with the [] or [] key.

The width can be set from 0 to 20 mm in increments of 5 mm (0" to 1" in increments of 1/4").

2 Press the [OK] key.

ERASE ADJUST

(When the dual function board is installed)

This is used to set the default erasure width. The factory default setting is "10 mm (1/2 inch)".

Select "ERASE ADJUST" and press the [OK] key. The following screen will appear.

ERASE ADJUST

mm (0~20)

1 Adjust the edge erase and centre erase width with the [] or [] key.

The edge erase width and the centre erase width share the same default value, which can be set from 0 to 20

mmin increments of 5 mm (0" to 1" in increments of 1/4").

2 Press the [OK] key.

CARD SHOT DEFAULT

(When the dual function board is installed)

This program is used to set the default dimensions that appear when the card shot size entry screen is displayed. The factory default settings are 86 mm (3-3/8") for the width (X) and 54 mm (2-1/8") for the length (Y).

Select "CARD SHOT DEFAULT" and press the [OK] key. The following screen will appear.

CARD SHOT DEFAULT

SIZE(mm)

X:

Y:

1 Select X or Y with the [ ] or [ ] key and adjust the corresponding default value with the [] or [] key.

2 Press the [OK] key.

DEFAULT TRAY SET

This program is used to set which tray is selected by default.

Trays that appear for selection will vary depending on the optional trays that have been installed.

The factory default setting is "TRAY 1".

86

Page 87 Page 89
Image 88
Page 87 Page 89
Contents Part 1 General Information Part 2 Copier OperationWarranty EMC this machine and peripheral devicesPart 1 General Information Trademark acknowledgments 250-sheet paper feed unit AR-D35 Product ConfigurationsMX-M200D Contents XY zoom copying Rotation copyMargin shift A Copy Erase copyFollow the cautions below when using this machine Laser Information For EuropeInstallation Requirements Environmental InformationSoftware setup guide Manuals Provided with the ProductMeaning of R in original and paper size indications Conventions used in this manualMain Features Network connection option Fax function optionEnvironment and people friendly design Part Names and Functions Document cover when installed Fusing unit paper guide Open to remove misfed paperSide cover Side cover handleOperation Panel Start key / indicator Paper Select keyCopy Ratio key Auto Image keyExample Copy mode Operation in COPY, PRINT, SCAN, and FAX ModesDisplay base screen Icons appearing in the special function icon displayTurning the Power on and OFF Power onPower OFF Power save modesDefault settings Loading PaperPaper Paper that can be used for automatic 2-sided printingSpecial paper Loading PaperLoading paper in a tray Open the bypass tray EnvelopesChanging the Paper Size Setting of a Tray SET A4RModes SETAuto Tray Switching Disabling Enabling Auto Tray SwitchingPaper Size SET Auditing Mode Number of Accounts in Auditing ModeUsing Auditing Mode When the copy job is finished, press the ACC.#-C keyTroubleshooting and Maintenance Troubleshooting MACHINE/COPYING ProblemsSelected paper size Paper misfeed has occurredPaper is not loaded properly Paper misfeed Too much paper is loaded in the trayOriginal is curled or folded Original has many solid black areas Original size is notAutomatically selected or Original is smaller than A5 5-1/2 x 8-1/2 sizeMessage Action Indicators and Display MessagesMB of expansion memory Removing Misfeeds Original Misfeed in the SPFRemove the misfed original Section aMisfeed in the Bypass Tray Section CMisfeed in the Machine Misfeed in aOpen the front cover Close the front cover and the side coverMisfeed in B Misfeed in Tray Misfeed in COpen the side cover Gently push tray 2 into the machine Remove the misfed paperGently close the side cover 250-sheet paper feed unit AR-D35Replacing the Toner Cartridge Close the front coverChecking the Total Output Count An A3 or 11 x 17 page is counted as two pagesCleaning the Document Glass SPF/DOCUMENT Cover Cleaning the MachineCleaning the Bypass Tray Paper Feed Roller Cleaning the Transfer Charger PositionAdjust the contrast with the or key Adjusting the Display ContrastSelect Display Contrast with the or key Optional Equipment Reversing Single Pass Feeder / Single Pass Feeder SpecificationsSheet Paper Feed Unit / 2 X 250-SHEET Paper Feed Unit Storage of Supplies Proper StorageStore the supplies in a location that is Store paper in the wrapper and lying flatPart 2 Copier Operation Page Normal Copying Copying from the document glassClose the SPF Make sure that the desired paper tray is selectedStream feeding mode Copying from the SPFPress the Start key to begin copying Copy will be delivered toAuto paper select mode Removing the document coverCopying books or originals with folds or creases Originals that can be used in the SPFMaking a Copy Darker or Lighter AutoText/photo TextSetting the Number of Copies Auto tray switchingImportant note when making a large number of copies Selecting the TraySelecting the Original Size ORIG. Size Enter InchORIG. Size Enter Select ORIG. Size Enter from the menu with the or keyEnter ExtraOKORIG. Size Enter ExtraReducing or Enlarging a Copy Automatic Ratio SelectionPress the Paper Select key to select the desired tray Press the Auto Image keyKey Select a larger preset ratio Key Select a smaller preset ratioKey Decrease the ratio in increments of 1% Key Increase the ratio in increments of 1%Okadjust XY ZoomSpecial Function XY ZoomAdjust OFFSet the vertical ratio with the , , , or keys Vertical ratio can now be selectedTWO-SIDED Copying TWO-SIDED CopyingOriginal → Paper One-sided original → Two sidesTWO-SIDED Copying of ONE-SIDED Originals CopyBinding Change OFF ModeCopy Mode Binding Change on Set the number of copies and press Start key Select 2 to 2 with the or key, or with the 2-SIDED Copy keyTo stop copying in the middle Copy Mode Select 2 to 1 with the or key, or with the 2-SIDED Copy keyTWO-SIDED Copies Using the Bypass Tray Place original B as shown belowVertically-oriented OriginalDual page Copy SpecialOkoff Checkmark appearsPress the Interrupt key Interrupting a Copy RUNReplace the previous originals and press the Start key Sort Mode Rotating the Image 90 DegreesCopies of multiple original pages can collated into sets Sort No sortOffset function enabled Offset function disabled SortNo Sort Press the Output keyPress the Paper Select key to select the desired paper tray 1 copy layoutsPattern BorderAN Okadjust Erasing Shadows around Edges of a Copy EraseDual EdgeSelect the erasure width with the or key Card Shot ModesCard Shot Card ShotFront side of the card is scanned Specifications Copies/min A4R 8-1/2 x 11RCopies/min 2 x 11R A4, B5, A5 8-1/2 x 25%, 50%, 64%, 77%, 95%, 100%, 121%, 129%, 141%, 200%, 400%Output tray specifications AppendixPrograms for Copy Mode Purpose of the System SettingsProgramming AN Administrator Password Programming AN Administrator Password Change Admin PWSystem Settings List Program nameSettings Using the System SettingsCopier Auditing Mode Reset AccountReset 1 ACC Account ControlACC. # Control ACC. # ControlDelete Change Cancel Jobs of Invalid Accounts Account LimitSingle ACC. Limit ACC. # SecurityWaiting Copy Lamp Setting USB2.0 ModeDevice Control Offset FunctionOperation Setting Disable Auto KEY Repeat Disable Paper Size SETKEY Touch Sound Keys Touch Sound AT Initial PointAuto Power SHUT-OFF Auto Power SHUT-OFF TimerPreheat Mode Energy SaveCopy Settings Stream Feeding Default Exposure Rotation CopySort Auto Select Resolution in AUTO/TEXT Mode Photo Mode DefaultDisable Auto Paper Selection Disable 2-SIDED CopyMaterial Safety Data Sheet Exposure Controls / Personal Protection Physical and Chemical Properties Ecological Information Supplier Identification Hazards Identification Physical and Chemical Properties No data are available Symbols / Numbers IndexTroubleshooting Normal copyingReducing or enlarging a copy 13, 31Troubleshooting Convenient copy functionsCopying, starting Two-sided copies of two-sided originals100 Administrator Password Number Factory Setting 102 103 Other Countries outside the EU Sharp Electronics Europe GmbH Sonninstraße 3, D-20097 HamburgMX-M160D/MX-M200D
Top Page Image Contents