Sharp MX-M200D, MX-M160D operation manual Replacing the Toner Cartridge, Close the front cover

Page 37

REPLACING THE TONER CARTRIDGE

When the toner replacement icon ( ) appears, little toner remains. Obtain a replacement cartridge as soon as possible. When the message " Add toner. Can not copy or print." appears in the display, the toner cartridge must be replaced before copying can be resumed. Follow the steps below to replace the toner cartridge.

• During a long copy run or when copying originals with many dark areas, the message "Toner replenishment in Note progress." may appear and copying will stop even though toner remains. The machine will feed toner for about

2 minutes. When the START indicator lights up, press the [START] key ( ) to resume copying.

•When the toner cartridge replacement required icon ( ) appears in the display, little toner remains and thus copies may be faint.

1 Open the front cover.

Push gently on both ends of the front cover to open it.

2 Pull the toner cartridge out while pressing on the toner cartridge lock release lever.

Toner cartridge

When pulling out the toner

lock release lever

cartridge, place your other hand

 

on the indentation of the

 

cartridge.

• After removing the toner cartridge, do not Caution shake it or tap it. Doing so may cause

toner to leak from the cartridge.

•

Put the old cartridge immediately in the

 

bag contained in the box of the new

 

cartridge.

•

Do not throw the toner cartridge

Warning

into a fire. Toner may fly and cause

 

burns.

•

Store toner cartridges out of the

 

reach of small children.

3 Remove the new toner cartridge from the bag. Grasp the cartridge on both sides and shake it horizontally four or five times.

4 or 5 times

• Do not hold the cartridge by the shutter. It Caution may fall. Grasp the hand grip when

holding the cartridge.

•Be sure to shake the cartridge only before the tape is removed.

4 While pressing down on the toner cartridge lock release lever, insert the toner cartridge along the guides all the way in.

If there is any dirt or dust on the

toner cartridge, remove it before 2 installing the cartridge.

5 Close the front cover.

 

The toner cartridge replacement

 

required icon ( ) will no longer

 

appear and copying will be

 

possible.

•

Even after a new toner cartridge is

Note

installed, the toner cartridge replacement

 

required indicator ( ) may still appear,

 

indicating that copying cannot be resumed

 

(toner is not fed sufficiently). In this case,

 

open and close the front cover. The

 

machine will feed toner again for about two

 

minutes and then copying can be resumed.

•Before closing the front cover, make sure that the toner cartridge is correctly installed.

•When closing the front cover, gently hold both ends.

35

Page 36 Page 38
Image 37
Page 36 Page 38
Contents Part 2 Copier Operation Part 1 General InformationEMC this machine and peripheral devices WarrantyPart 1 General Information Trademark acknowledgments 250-sheet paper feed unit AR-D35 Product ConfigurationsMX-M200D Contents Rotation copy XY zoom copyingMargin shift A Copy Erase copyFollow the cautions below when using this machine For Europe Laser InformationEnvironmental Information Installation RequirementsManuals Provided with the Product Software setup guideMeaning of R in original and paper size indications Conventions used in this manualMain Features Network connection option Fax function optionEnvironment and people friendly design Part Names and Functions Fusing unit paper guide Open to remove misfed paper Document cover when installedSide cover Side cover handleOperation Panel Paper Select key Start key / indicatorCopy Ratio key Auto Image keyOperation in COPY, PRINT, SCAN, and FAX Modes Example Copy modeDisplay base screen Icons appearing in the special function icon displayPower on Turning the Power on and OFFPower OFF Power save modesLoading Paper Default settingsPaper Paper that can be used for automatic 2-sided printingSpecial paper Loading PaperLoading paper in a tray Envelopes Open the bypass traySET A4R Changing the Paper Size Setting of a TrayModes SETAuto Tray Switching Disabling Enabling Auto Tray SwitchingPaper Size SET Number of Accounts in Auditing Mode Auditing ModeUsing Auditing Mode When the copy job is finished, press the ACC.#-C keyTroubleshooting and Maintenance MACHINE/COPYING Problems TroubleshootingPaper misfeed has occurred Selected paper sizePaper is not loaded properly Paper misfeed Too much paper is loaded in the trayOriginal has many solid black areas Original size is not Original is curled or foldedAutomatically selected or Original is smaller than A5 5-1/2 x 8-1/2 sizeMessage Action Indicators and Display MessagesMB of expansion memory Original Misfeed in the SPF Removing MisfeedsRemove the misfed original Section aSection C Misfeed in the Bypass TrayMisfeed in a Misfeed in the MachineOpen the front cover Close the front cover and the side coverMisfeed in B Misfeed in C Misfeed in TrayRemove the misfed paper Open the side cover Gently push tray 2 into the machineGently close the side cover 250-sheet paper feed unit AR-D35Close the front cover Replacing the Toner CartridgeAn A3 or 11 x 17 page is counted as two pages Checking the Total Output CountCleaning the Document Glass SPF/DOCUMENT Cover Cleaning the MachineCleaning the Bypass Tray Paper Feed Roller Position Cleaning the Transfer ChargerAdjust the contrast with the or key Adjusting the Display ContrastSelect Display Contrast with the or key Optional Equipment Reversing Single Pass Feeder / Single Pass Feeder SpecificationsSheet Paper Feed Unit / 2 X 250-SHEET Paper Feed Unit Proper Storage Storage of SuppliesStore the supplies in a location that is Store paper in the wrapper and lying flatPart 2 Copier Operation Page Copying from the document glass Normal CopyingClose the SPF Make sure that the desired paper tray is selectedCopying from the SPF Stream feeding modePress the Start key to begin copying Copy will be delivered toRemoving the document cover Auto paper select modeCopying books or originals with folds or creases Originals that can be used in the SPFAuto Making a Copy Darker or LighterText/photo TextAuto tray switching Setting the Number of CopiesImportant note when making a large number of copies Selecting the TrayORIG. Size Enter Inch Selecting the Original SizeORIG. Size Enter Select ORIG. Size Enter from the menu with the or keyExtra EnterOKORIG. Size Enter ExtraAutomatic Ratio Selection Reducing or Enlarging a CopyPress the Paper Select key to select the desired tray Press the Auto Image keyKey Select a smaller preset ratio Key Select a larger preset ratioKey Decrease the ratio in increments of 1% Key Increase the ratio in increments of 1%XY Zoom OkadjustSpecial Function XY ZoomOFF AdjustSet the vertical ratio with the , , , or keys Vertical ratio can now be selectedTWO-SIDED Copying TWO-SIDED CopyingOriginal → Paper One-sided original → Two sidesCopy TWO-SIDED Copying of ONE-SIDED OriginalsBinding Change OFF ModeCopy Mode Binding Change on Set the number of copies and press Start key Select 2 to 2 with the or key, or with the 2-SIDED Copy keyTo stop copying in the middle Select 2 to 1 with the or key, or with the 2-SIDED Copy key Copy ModePlace original B as shown below TWO-SIDED Copies Using the Bypass TrayVertically-oriented OriginalSpecial Dual page CopyOkoff Checkmark appearsPress the Interrupt key Interrupting a Copy RUNReplace the previous originals and press the Start key Rotating the Image 90 Degrees Sort ModeCopies of multiple original pages can collated into sets Sort No sortSort Offset function enabled Offset function disabledNo Sort Press the Output key1 copy layouts Press the Paper Select key to select the desired paper trayBorder PatternAN Okadjust Erase Erasing Shadows around Edges of a CopyDual EdgeSelect the erasure width with the or key Modes Card ShotCard Shot Card ShotFront side of the card is scanned Copies/min A4R 8-1/2 x 11R SpecificationsCopies/min 2 x 11R A4, B5, A5 8-1/2 x 25%, 50%, 64%, 77%, 95%, 100%, 121%, 129%, 141%, 200%, 400%Appendix Output tray specificationsPrograms for Copy Mode Purpose of the System SettingsProgramming AN Administrator Password Change Admin PW Programming AN Administrator PasswordProgram name System Settings ListSettings Using the System SettingsCopier Reset Account Auditing ModeReset 1 ACC Account ControlACC. # Control ACC. # ControlDelete Change Account Limit Cancel Jobs of Invalid AccountsSingle ACC. Limit ACC. # SecurityUSB2.0 Mode Waiting Copy Lamp SettingDevice Control Offset FunctionOperation Setting Disable Paper Size SET Disable Auto KEY RepeatKEY Touch Sound Keys Touch Sound AT Initial PointAuto Power SHUT-OFF Timer Auto Power SHUT-OFFPreheat Mode Energy SaveCopy Settings Stream Feeding Default Exposure Rotation CopySort Auto Select Photo Mode Default Resolution in AUTO/TEXT ModeDisable Auto Paper Selection Disable 2-SIDED CopyMaterial Safety Data Sheet Exposure Controls / Personal Protection Physical and Chemical Properties Ecological Information Supplier Identification Hazards Identification Physical and Chemical Properties No data are available Index Symbols / NumbersNormal copying TroubleshootingReducing or enlarging a copy 13, 31Convenient copy functions TroubleshootingCopying, starting Two-sided copies of two-sided originals100 Administrator Password Number Factory Setting 102 103 Other Countries outside the EU Sonninstraße 3, D-20097 Hamburg Sharp Electronics Europe GmbHMX-M160D/MX-M200D
Top Page Image Contents