Sharp AL-1670 operation manual Copier Installation, Do not install your copier in areas that are

Page 10

COPIER INSTALLATION

GETTING STARTED

Copier installation

Improper installation may damage the copier. Please note the following during initial installation and whenever the copier is moved.

If the copier is moved from a cool place to a warm place, condensation may form inside the copier. Operation in this condition will cause poor copy quality and malfunctions. Leave the copier at room temperature for at least 2 hours before use.

Do not install your copier in areas that are:

● damp, humid, or very dusty

● exposed to direct sunlight

● poorly ventilated

●subject to extreme temperature or humidity changes, e.g., near an air conditioner or heater.

The copier should be installed near an accessible power outlet for easy connection.

Be sure to connect the power cord only to a power outlet that meets the specified voltage and current requirements.

Also make certain the outlet is properly grounded.

Connect the copier to a power outlet which is not used for other electric appliances. If a lighting fixture is connected to the same outlet, the light may flicker.

Be sure to allow the required space around the machine for servicing and proper ventilation.

4" (10 cm)

A small amount of ozone is produced within the copier during operation.The emission level is insufficient to cause any health hazard.

NOTE:

The present recommended long term exposure limit for ozone is 0.1 ppm (0.2 mg/m3) calculated as an 8 hr. time-weighted average concentration.

However, since the small amount that is emitted may have an objectionable odor, it is advisable to place the copier in a ventilated area.

8

Image 10

Contents AL-1670 For Your Protection Contents Safety Precautions Main Features Part Names and Functions Part Names and Functions Original Size Enter key and indicators p Operation panel and keys for printer featuresAUTO/MANUAL/PHOTO / / key and indicators p Paper Size indicators@2Light and dark keys and indicators Key and indicators@1ORIGINAL Data indicator @3AUTO Image key and indicator pCopier Installation Do not install your copier in areas that areGetting Started Checking Packed Components and Accessories UnpackingSET-UP Install the TD cartridgeGently lift and pull out the paper tray until it stops Front of the paper tray Turn the power switch on Load copy paperSET-UP Store the pressure plate lock which has been removedLoading Copy Paper Push the paper tray firmly back into the copierLoading Copy Paper Press the Start key and then the Paper Size 11ENTER key Turn the power switch on Using the SPFNormal Copying Normal Copying Set the number of copies using the two copy quantity KeysStream feeding mode Press the Start keyUsing the original table Adjust the copy densityNormal Copying Press the Auto Image Key REDUCTION/ENLARGEMENT/ZOOMAutomatic Enter the number of copies Press the Start keyREDUCTION/ENLARGEMENT/ZOOM ManualBypass Feed special paper Unfold the bypass trayBypass Feed special paper TWO-SIDED Copying SORT/GROUP Sort modeGroup mode Offset stackSORT/GROUP Copying in the sort modeSet the originals face up in the document feeder tray Interrupting a Copy RUN When all Interrupt copies are finished, pressPress the Interrupt key Automatic Exposure Adjustment Toner Save Mode To enter the toner save mode, press the light keyXY Zoom Press the copy ratio display KeyXY Zoom Set the number of copies and press the Start keyReverse Dual page Copy Press the Dual page Copy keyRotation Copying 1 or 4 Select the desired pattern number using copy quantity keys Press the 2 in 1 / 4 in 1 key to complete the selectionUse the Tray Select Press the Erase key to select the desired erase modeErase Key to select the paper trayMargin Shift TD Cartridge Replacement Genuine SuppliesTD Cartridge Replacement Drum Cartridge Replacement Drum Cartridge Replacement First confirm the misfeed location Misfeed RemovalMisfeed in the SPF Open the feeding roller cover and pull the original gentlyMisfeed in the copier Misfeed RemovalMisfeed in the bypass tray If the misfed original cannot be removed in steps 1Removing it Fusing unit is hot. Take care in removing paperPush gently the right side of the front cover to open Cover Misfeed in the transport area Close the side cover by pressing the handle on the cover Misfeed in the upper paper trayMisfeed in the lower paper tray Grasp the handle of the lower side cover and gently openRemove the misfed paper Close the paper tray Close the lower side coverList of user programs Setting the user programsUser Programs Press and hold the light key for more thanEnter a program number using the left copy quantity Key User ProgramsEntered value will be stored Preheat mode Power Save ModesAuto power shut-off mode Copying from the preheat mode Power Save ModesSetting the power save modes Copying from the auto power shut-off modeBypass tray paper feed roller User MaintenanceOriginal table and document feeder cover Transfer chargerCharger cleaner out by holding the tab User MaintenanceGently lift and pull out the upper paper tray and take Problem Solution Copier TROUBLE?Copier TROUBLE? Self-diagnostic functionExample Supply part numbers SuppliesTypes and sizes of copy paper Supply listProper storage SuppliesGenuine supplies statement Store the supplies in a location that isMoving Instructions Turn the power switch off and disconnect the power CordPush the paper tray back into the copier Specifications CopierSpecifications Single Pass FeederIndex Index Material Safety Data Sheet Flash Point Method Used Ignition TemperatureSpecial Fire Fighting Procedure Flammable LimitsOther Limits Ingredients CAS No ProportionHealth Hazards None required under normal use Page Sharp Corporation