Sharp AL-1670 Power Save Modes, Setting the power save modes, Copying from the preheat mode

Page 55

POWER SAVE MODES

Setting the power save modes

The time that elapses before the copier enters a power save mode after any operation is made can be set manually. This time is set with user program No. 2 for the preheat mode and user program No. 3 for the auto power shut-off mode. For these settings, see page 49.

●The copier will enter the preheat mode first and then the auto power shut- off mode after a preset time has elapsed when no copier operation has been made.

●If conflicting settings are made with user programs No. 3 and No.5, the last program set will have priority.

Copying from the preheat mode

Make desired copier selections and press the START

( ) key using the normal copying procedure.

●When any key input is made or any other copier operation is made, the POWER SAVE indicator will start to blink.

●When the START key is pressed, the START key indicator will go out and copying will start within 10 seconds. The POWER SAVE indicator will go out when copying starts.

Copying from the auto power shut-off mode

1	Press the START ( ) key.
	● The copier will exit the auto power shut-off mode and the POWER

SAVE indicator will start to blink.

Power save modes

Make desired copier selections and press the START

2 ( ) key using the normal copying procedure.

●It will take approximately 35 seconds for the copier to start copying. However, you can make desired settings and press the START key during warm-up. Copying will start after warm-up is finished.

GENERAL INFORMATION

53

Image 55

Contents AL-1670 For Your Protection Contents Safety Precautions Main Features Part Names and Functions Part Names and Functions Paper Size indicators Operation panel and keys for printer featuresAUTO/MANUAL/PHOTO / / key and indicators p Original Size Enter key and indicators p@3AUTO Image key and indicator p Key and indicators@1ORIGINAL Data indicator @2Light and dark keys and indicatorsDo not install your copier in areas that are Copier InstallationGetting Started Unpacking Checking Packed Components and AccessoriesSET-UP Install the TD cartridgeGently lift and pull out the paper tray until it stops Store the pressure plate lock which has been removed Turn the power switch on Load copy paperSET-UP Front of the paper trayPush the paper tray firmly back into the copier Loading Copy PaperLoading Copy Paper Press the Start key and then the Paper Size 11ENTER key Turn the power switch on Using the SPFNormal Copying Press the Start key Set the number of copies using the two copy quantity KeysStream feeding mode Normal CopyingAdjust the copy density Using the original tableNormal Copying Enter the number of copies Press the Start key REDUCTION/ENLARGEMENT/ZOOMAutomatic Press the Auto Image KeyManual REDUCTION/ENLARGEMENT/ZOOMUnfold the bypass tray Bypass Feed special paperBypass Feed special paper TWO-SIDED Copying Offset stack Sort modeGroup mode SORT/GROUPSORT/GROUP Copying in the sort modeSet the originals face up in the document feeder tray Interrupting a Copy RUN When all Interrupt copies are finished, pressPress the Interrupt key Automatic Exposure Adjustment To enter the toner save mode, press the light key Toner Save ModePress the copy ratio display Key XY ZoomSet the number of copies and press the Start key XY ZoomReverse Press the Dual page Copy key Dual page CopyRotation Copying 1 or 4 Press the 2 in 1 / 4 in 1 key to complete the selection Select the desired pattern number using copy quantity keysKey to select the paper tray Press the Erase key to select the desired erase modeErase Use the Tray SelectMargin Shift Genuine Supplies TD Cartridge ReplacementTD Cartridge Replacement Drum Cartridge Replacement Drum Cartridge Replacement Open the feeding roller cover and pull the original gently Misfeed RemovalMisfeed in the SPF First confirm the misfeed locationIf the misfed original cannot be removed in steps 1 Misfeed RemovalMisfeed in the bypass tray Misfeed in the copierRemoving it Fusing unit is hot. Take care in removing paperPush gently the right side of the front cover to open Cover Misfeed in the transport area Grasp the handle of the lower side cover and gently open Misfeed in the upper paper trayMisfeed in the lower paper tray Close the side cover by pressing the handle on the coverClose the paper tray Close the lower side cover Remove the misfed paperPress and hold the light key for more than Setting the user programsUser Programs List of user programsUser Programs Enter a program number using the left copy quantity KeyEntered value will be stored Preheat mode Power Save ModesAuto power shut-off mode Copying from the auto power shut-off mode Power Save ModesSetting the power save modes Copying from the preheat modeTransfer charger User MaintenanceOriginal table and document feeder cover Bypass tray paper feed rollerCharger cleaner out by holding the tab User MaintenanceGently lift and pull out the upper paper tray and take Copier TROUBLE? Problem SolutionCopier TROUBLE? Self-diagnostic functionExample Supply list SuppliesTypes and sizes of copy paper Supply part numbersStore the supplies in a location that is SuppliesGenuine supplies statement Proper storageMoving Instructions Turn the power switch off and disconnect the power CordPush the paper tray back into the copier Copier SpecificationsSingle Pass Feeder SpecificationsIndex Index Material Safety Data Sheet Flammable Limits Ignition TemperatureSpecial Fire Fighting Procedure Flash Point Method UsedOther Limits Ingredients CAS No ProportionHealth Hazards None required under normal use Page Sharp Corporation