Sharp AL-1670 operation manual

Page 71

WARNING:

FCC Regulations state that any unauthorized changes or modifications to this equipment not expressly approved by the manufacturer could void the user's authority to operate this equipment.

Note:

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment gen- erates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the operation manual, may cause harmful interfer- ence to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

Shielded cables must be used with this equipment to maintain compliance with FCC regulations.

Image 71

Contents AL-1670 For Your Protection Contents Safety Precautions Main Features Part Names and Functions Part Names and Functions Paper Size indicators Operation panel and keys for printer featuresAUTO/MANUAL/PHOTO / / key and indicators p Original Size Enter key and indicators p@3AUTO Image key and indicator p Key and indicators@1ORIGINAL Data indicator @2Light and dark keys and indicatorsDo not install your copier in areas that are Copier InstallationGetting Started Unpacking Checking Packed Components and AccessoriesGently lift and pull out the paper tray until it stops Install the TD cartridgeSET-UP Store the pressure plate lock which has been removed Turn the power switch on Load copy paperSET-UP Front of the paper trayPush the paper tray firmly back into the copier Loading Copy PaperLoading Copy Paper Press the Start key and then the Paper Size 11ENTER key Normal Copying Using the SPFTurn the power switch on Press the Start key Set the number of copies using the two copy quantity KeysStream feeding mode Normal CopyingAdjust the copy density Using the original tableNormal Copying Enter the number of copies Press the Start key REDUCTION/ENLARGEMENT/ZOOMAutomatic Press the Auto Image KeyManual REDUCTION/ENLARGEMENT/ZOOMUnfold the bypass tray Bypass Feed special paperBypass Feed special paper TWO-SIDED Copying Offset stack Sort modeGroup mode SORT/GROUPSet the originals face up in the document feeder tray Copying in the sort modeSORT/GROUP Press the Interrupt key When all Interrupt copies are finished, pressInterrupting a Copy RUN Automatic Exposure Adjustment To enter the toner save mode, press the light key Toner Save ModePress the copy ratio display Key XY ZoomSet the number of copies and press the Start key XY ZoomReverse Press the Dual page Copy key Dual page CopyRotation Copying 1 or 4 Press the 2 in 1 / 4 in 1 key to complete the selection Select the desired pattern number using copy quantity keysKey to select the paper tray Press the Erase key to select the desired erase modeErase Use the Tray SelectMargin Shift Genuine Supplies TD Cartridge ReplacementTD Cartridge Replacement Drum Cartridge Replacement Drum Cartridge Replacement Open the feeding roller cover and pull the original gently Misfeed RemovalMisfeed in the SPF First confirm the misfeed locationIf the misfed original cannot be removed in steps 1 Misfeed RemovalMisfeed in the bypass tray Misfeed in the copierPush gently the right side of the front cover to open Cover Fusing unit is hot. Take care in removing paperRemoving it Misfeed in the transport area Grasp the handle of the lower side cover and gently open Misfeed in the upper paper trayMisfeed in the lower paper tray Close the side cover by pressing the handle on the coverClose the paper tray Close the lower side cover Remove the misfed paperPress and hold the light key for more than Setting the user programsUser Programs List of user programsUser Programs Enter a program number using the left copy quantity KeyEntered value will be stored Auto power shut-off mode Power Save ModesPreheat mode Copying from the auto power shut-off mode Power Save ModesSetting the power save modes Copying from the preheat modeTransfer charger User MaintenanceOriginal table and document feeder cover Bypass tray paper feed rollerGently lift and pull out the upper paper tray and take User MaintenanceCharger cleaner out by holding the tab Copier TROUBLE? Problem SolutionExample Self-diagnostic functionCopier TROUBLE? Supply list SuppliesTypes and sizes of copy paper Supply part numbersStore the supplies in a location that is SuppliesGenuine supplies statement Proper storagePush the paper tray back into the copier Turn the power switch off and disconnect the power CordMoving Instructions Copier SpecificationsSingle Pass Feeder SpecificationsIndex Index Material Safety Data Sheet Flammable Limits Ignition Temperature Special Fire Fighting Procedure Flash Point Method UsedHealth Hazards Ingredients CAS No ProportionOther Limits None required under normal use Page Sharp Corporation