Sharp AL-1670 operation manual Safety Precautions

Page 4

CAUTIONS

GETTING STARTED

Cautions

Follow the cautions below when using this copier.

●The fusing area is hot. Exercise care in this area when removing misfed paper.

●Do not look directly at the light source. Doing so may damage your eyes.

●The socket-outlet shall be installed near the equipment and shall be easily accessible.

●Place the copier on a firm, level surface.

● Do not install the copier in a humid or dusty location.

● When the copier is not used for a long time, for example, during prolonged holidays, turn the power switch off and remove the power cord from the outlet.

●When moving the copier, be sure to turn the power switch off and remove the power cord from the outlet.

●Do not cover the copier with a dust cover, cloth or plastic film while the power is on. Doing so may prevent heat dissipation, damaging the copier.

SAFETY PRECAUTIONS

This Digital Copier is rated Class 1 and complies with 21 CFR 1040.10 and 1040.11 of the CDRH standards. This means that the copier does not produce hazardous laser radiation. For your safety, observe the precautions below.

●Do not remove the cabinet, operation panel or any other covers.

●The copier’s exterior covers contain several safety interlock switches. Do not bypass any safety interlock by inserting wedges or other items into switch slots.

Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous laser radiation exposure.

2

Image 4

Contents AL-1670 For Your Protection Contents Safety Precautions Main Features Part Names and Functions Part Names and Functions Operation panel and keys for printer features AUTO/MANUAL/PHOTO / / key and indicators pOriginal Size Enter key and indicators p Paper Size indicatorsKey and indicators @1ORIGINAL Data indicator@2Light and dark keys and indicators @3AUTO Image key and indicator pCopier Installation Do not install your copier in areas that areGetting Started Checking Packed Components and Accessories UnpackingSET-UP Install the TD cartridgeGently lift and pull out the paper tray until it stops Turn the power switch on Load copy paper SET-UPFront of the paper tray Store the pressure plate lock which has been removedLoading Copy Paper Push the paper tray firmly back into the copierLoading Copy Paper Press the Start key and then the Paper Size 11ENTER key Turn the power switch on Using the SPFNormal Copying Set the number of copies using the two copy quantity Keys Stream feeding modeNormal Copying Press the Start keyUsing the original table Adjust the copy densityNormal Copying REDUCTION/ENLARGEMENT/ZOOM AutomaticPress the Auto Image Key Enter the number of copies Press the Start keyREDUCTION/ENLARGEMENT/ZOOM ManualBypass Feed special paper Unfold the bypass trayBypass Feed special paper TWO-SIDED Copying Sort mode Group modeSORT/GROUP Offset stackSORT/GROUP Copying in the sort modeSet the originals face up in the document feeder tray Interrupting a Copy RUN When all Interrupt copies are finished, pressPress the Interrupt key Automatic Exposure Adjustment Toner Save Mode To enter the toner save mode, press the light keyXY Zoom Press the copy ratio display KeyXY Zoom Set the number of copies and press the Start keyReverse Dual page Copy Press the Dual page Copy keyRotation Copying 1 or 4 Select the desired pattern number using copy quantity keys Press the 2 in 1 / 4 in 1 key to complete the selectionPress the Erase key to select the desired erase mode EraseUse the Tray Select Key to select the paper trayMargin Shift TD Cartridge Replacement Genuine SuppliesTD Cartridge Replacement Drum Cartridge Replacement Drum Cartridge Replacement Misfeed Removal Misfeed in the SPFFirst confirm the misfeed location Open the feeding roller cover and pull the original gentlyMisfeed Removal Misfeed in the bypass trayMisfeed in the copier If the misfed original cannot be removed in steps 1Removing it Fusing unit is hot. Take care in removing paperPush gently the right side of the front cover to open Cover Misfeed in the transport area Misfeed in the upper paper tray Misfeed in the lower paper trayClose the side cover by pressing the handle on the cover Grasp the handle of the lower side cover and gently openRemove the misfed paper Close the paper tray Close the lower side coverSetting the user programs User ProgramsList of user programs Press and hold the light key for more thanEnter a program number using the left copy quantity Key User ProgramsEntered value will be stored Preheat mode Power Save ModesAuto power shut-off mode Power Save Modes Setting the power save modesCopying from the preheat mode Copying from the auto power shut-off modeUser Maintenance Original table and document feeder coverBypass tray paper feed roller Transfer chargerCharger cleaner out by holding the tab User MaintenanceGently lift and pull out the upper paper tray and take Problem Solution Copier TROUBLE?Copier TROUBLE? Self-diagnostic functionExample Supplies Types and sizes of copy paperSupply part numbers Supply listSupplies Genuine supplies statementProper storage Store the supplies in a location that isMoving Instructions Turn the power switch off and disconnect the power CordPush the paper tray back into the copier Specifications CopierSpecifications Single Pass FeederIndex Index Material Safety Data Sheet Ignition Temperature Special Fire Fighting ProcedureFlash Point Method Used Flammable LimitsOther Limits Ingredients CAS No ProportionHealth Hazards None required under normal use Page Sharp Corporation