Motorola T1/E1 manual Procedure 16 Selecting line type T1 or E1 using the EMS, Select Configure T1

Page 49

Canopy T1/E1 Multiplexer	September 2004
	T1/E1 Multiplexer FPGA Version 3.4

2.5.3Select Line Type T1 or E1

Procedure 16: Selecting line type T1 or E1 using the EMS

Follow these steps to configure line coding for the Canopy T1/E1 Multiplexer from the EMS.

NOTE: Selecting either T1 or E1 will configure all 4 channels.

1.From main menu EMS, select the Configuration (Config) option.

2.Select Configure Line Type.

RESULT: The Line Config dialogue box opens.

3.Click ↓.

RESULT: The dropdown list to specify the coding technique T1 channel opens.

4.Click on the appropriate line coding technique for the T1channel being configured.

5.Click on the tab for the next Channel to configure line coding for channel.

6.To configure the line coding technique for each channel, repeat Steps 3 and 4.

7.When all channels are configured, select the File→Reset menu option. RESULT: A confirmation window pops up.

8.To reset the system, select Yes.

9.Select Close.

RESULT: The dialogue box closes and you are returned to the EMS main menu.

end of procedure

2.5.4Select Line Coding

Procedure 17: Configuring T1 line coding using the EMS

Follow these steps to configure T1 line coding from the EMS.

1.From main menu EMS, select the Configuration (Config) option.

2.Select Configure T1.

RESULT: The Config dialogue box opens.

3.Click ↓.

RESULT: The dropdown list to specify the coding technique T1 channel opens.

4.Click on the appropriate line coding technique for the T1channel being configured.

NOTE: You must select a coding technique: either B8ZS or AMI.

5.Click on the tab for the next Channel to configure line coding for channel. NOTE: If the system has been reset, clicking the Refresh button will replace the displayed values with currently-programmed values.

6.To configure the line coding technique for each other channel, repeat Steps 3 and 4.

7.Select Close to close the dialogue box once all channels are configured. RESULT: You are returned to the EMS main menu.

end of procedure

Issue 3

Page 49 of 73

Image 49

Contents Canopy T1/E1 Multiplexer User Guide T1E1Mux-UG-en Issue SeptemberTable of Contents Managing Your Canopy T1/E1 Multiplexers List of Figures List of Tables List of Procedures New in This Issue Using this User GuideUsing the Latest Information Searching This User GuideVariable width bold Font Type of InformationConstant width bold Admonition General Message LabelGetting Additional Help Introduction to Canopy T1/E1 MultiplexerSending Feedback Canopy T1/E1 Multiplexer with Canopy BHs Ethernet InterfaceIDU Physical Description StandardsRear Panel Rear panel with standard 110-v source power supply Canopy T1/E1 Multiplexer LED indicator descriptions LED status indicator descriptionsFront Panel Status LedsSpecifications FeaturesPhysical Specifications Canopy T1/E1 Multiplexer physical specificationsT1 port specifications Technical SpecificationsT1 framing specifications E1 port specificationsE1 framing specifications Configuration Settings from Canopy FactoryLocal terminal and control interface specifications Bit Handling CapabilityProduct Labels Power AdaptersFunctional Description of the Canopy T1/E1 Multiplexer License KeysE1 Channel Mode T1 Channel ModeChannel Modes Encoding1 in 15 Requirement AMI Alternate Mark Inversion AMIBinary Eight Zero Substitution Coding Timing SignalingHigh Density Bipolar Order Three Encoding Master and Secondary Clocks Frequency off-set by clock typeLoopback Timing Mode Loss of Clock SignalRecovered Timing Mode Timing ModesNetwork Timing Scenarios Slave timing set to Recovered modeEthernet Throughput Alarms Round‐Trip Packet DelayVlan Support Power Supply Unit Safety InformationCompliance Lightning ProtectionPackage Contents Installation ProceduresPreparing for Installation and Setup Mounting the Canopy T1/E1 MultiplexerEnd of procedure Connecting the Canopy T1/E1 MultiplexerT1/E1 port connector pin-out Pin Designation DirectionRJ-45 Connector Connecting Power to the Canopy T1/E1 MultiplexerProcedure 2 Connecting cables to T1/E1 unit Canopy BH PinProcedure 4 Connecting the −48 v DC power source Procedure 3 Connecting the AC adapter +3.3 v DC power sourceInstalling Software from the CD‐ROM Initial Configuration ProceduresProcedure 5 Installing Software from the CD-ROM Issue the Start-Run-d/setup sequenceFile drop-down menu in GUI Using EMS Software to Configure the UnitConfiguring the Canopy T1/E1 Multiplexer using the CLI Accessing the CLI using a PC + HyperTerminalProcedure 6 Configuring serial port Parameter ValueCommand Line Interface window Creating a Login AccountChanging the Administrator Password Configuration Procedures Using the CLIProcedure 7 Changing Administrator password using the CLI Logging into the SystemSelect Line Type T1 or E1 Procedure 8 Selecting line type T1 or E1 using the CLIAction Steps Enter get line typeSelect Line Coding Procedure 9 Configuring line coding using the CLIEnter set line 1/2/3/4 code HDB3/B8ZS/AMI Enter get line codeProcedure 10 Configuring the Ethernet ports using the CLI Configure PortsAction Enter set canopy port auto negotiation on/offDB 266-399 / 1.8 dB 399-533 / 2.4 dB 533-655 Procedure 11 Configuring the T1 ports using the CLIEnter set master clock reference line 1/2/3/4 Enter set clock source loopback/recoveredEnter set secondary clock reference line 1/2/3/4 Enter set line 1/2/3/4 code HDB3/AMI Procedure 12 Configuring the E1 ports using the CLISet clock source loopback Set clock source recoveredProcedure 13 Configuring timing using the CLI Configure TimingEnd of procedure Configuration Procedures Using the EMSProcedure 14 Logging in using the EMS Login dialogue box File→Command Line Terminal from the EMS Main menu T1/E1 Multiplexer EMS main menu End of procedureChanging the Administrator Password Select Configure Line Type Procedure 16 Selecting line type T1 or E1 using the EMSProcedure 17 Configuring T1 line coding using the EMS Select Configure T1Select Configure E1 Procedure 18 Configuring E1 line coding using the EMSProcedure 19 Configuring the Ethernet ports using the EMS Click ↓ for Master Clock Reference Line Procedure 21 Configuring the E1 ports using the EMSClick ↓ for Secondary Clock Reference Line Procedure 22 Configuring timing using the EMS Remote management overview Remote Management Through Control PortEnter get alarms Procedure 23 Displaying the alarms using the CLISelect the Alarms→T1/E1 Alarms menu Procedure 24 Displaying alarms using the EMSProcedure 25 Resetting the system using the CLI System ResetProcedure 26 Resetting the system using the EMS T1/E1 Loopback Canopy T1/E1 Multiplexer in T1/E1 Loopback modeInvoking a T1/E1 Loopback Using the EMS Invoking a T1/E1 Loopback using the CLIProcedure 27 Invoking a T1/E1 loopback using the CLI Procedure 28 Invoking a T1/E1 loopback using the EMSFirmware Upgrades Measurements from DiagnosticsComparison of diagnostic measurements Procedure 29 Upgrading firmwareClick Download Fpga revision details screen End of procedureT1/E1 Port Upgrade window License KEY UpgradesInvalid key entry window Software License Terms and Conditions Terms of WarrantyCanopy T1/E1 Multiplexer Obtaining Technical Support Hardware Warranty in U.SInvoking Your Warranty Rights Desired Action Syntax, Response, and Description CLI Commands to GET Status InformationEnter get canopy port auto negotiation Enter get lan port auto negotiationEnter get code line 1/2/3/4 Enter get line 1/2/3/4 lengthEnter get master clock reference line Enter get clock sourceEnter get secondary clock reference line Enter get firmware revision Enter get loopback line 1/2/3/4Regulatory Compliance Information Department of Communications Canada TRADEMARKS, Product NAMES, and Service NamesEuropean Telecommunications Standards Institute Canadian Compliance StatementReferences