Motorola T1/E1 Accessing the CLI using a PC + HyperTerminal, Procedure 6 Configuring serial port

Page 34

Canopy T1/E1 Multiplexer

September 2004

 

T1/E1 Multiplexer FPGA Version 3.4

2.3.3Accessing the CLI using a PC + HyperTerminal

The Command Line Interface (CLI) is accessed using a PC with that includes a terminal emulation package such as HyperTerminal®.

NOTE: The device is only accessible through the serial port.

2.3.4Configuring the Canopy T1/E1 Multiplexer using the CLI

Before you use the CLI to configure the Canopy T1/E1 Multiplexer, you must configure the PC serial port.

Procedure 6: Configuring serial port

Use this procedure to access the CLI using a terminal emulation program such as HyperTerminal.®

1.Connect the serial cable from the DB9 serial port on a PC to the Serial port on the Canopy T1/E1 Multiplexer. The DB9 connector on Canopy T1/E1 Multiplexer is female; the cable from the PC is male. A straight-through cable is required.

2.Start HyperTerminal or another terminal emulation program.

3.Set the terminal emulation program to emulate a VT100 terminal with the following settings:

Parameter

Value

 

 

Bits per second

19200

 

 

Data bits

8

 

 

Parity

none

 

 

Stop bits

1

 

 

Flow control

none

 

 

4.Press Enter.

The Canopy T1/E1 Multiplexer Login menu is displayed. RESULT: The signal port is configured.

end of procedure

To use the CLI, select Command Line Interface terminal from the File drop-down menu (illustrated in Figure 14 on Page 33). The Command Line Interface window opens, as shown in Figure 16.

Issue 3

Page 34 of 73

Image 34
Contents T1E1Mux-UG-en Issue September Canopy T1/E1 Multiplexer User GuideTable of Contents Managing Your Canopy T1/E1 Multiplexers List of Figures List of Tables List of Procedures Using the Latest Information Using this User GuideNew in This Issue Searching This User GuideConstant width bold Font Type of InformationVariable width bold Admonition General Message LabelGetting Additional Help Introduction to Canopy T1/E1 MultiplexerSending Feedback Ethernet Interface Canopy T1/E1 Multiplexer with Canopy BHsIDU Physical Description StandardsRear Panel Rear panel with standard 110-v source power supply Canopy T1/E1 Multiplexer Front Panel LED status indicator descriptionsLED indicator descriptions Status LedsPhysical Specifications FeaturesSpecifications Canopy T1/E1 Multiplexer physical specificationsT1 framing specifications Technical SpecificationsT1 port specifications E1 port specificationsLocal terminal and control interface specifications Configuration Settings from Canopy FactoryE1 framing specifications Bit Handling CapabilityFunctional Description of the Canopy T1/E1 Multiplexer Power AdaptersProduct Labels License KeysChannel Modes T1 Channel ModeE1 Channel Mode Encoding1 in 15 Requirement AMI Alternate Mark Inversion AMIBinary Eight Zero Substitution Coding Timing SignalingHigh Density Bipolar Order Three Encoding Frequency off-set by clock type Master and Secondary ClocksRecovered Timing Mode Loss of Clock SignalLoopback Timing Mode Timing ModesSlave timing set to Recovered mode Network Timing ScenariosEthernet Throughput Alarms Round‐Trip Packet DelayVlan Support Compliance Safety InformationPower Supply Unit Lightning ProtectionPreparing for Installation and Setup Installation ProceduresPackage Contents Mounting the Canopy T1/E1 MultiplexerT1/E1 port connector pin-out Connecting the Canopy T1/E1 MultiplexerEnd of procedure Pin Designation DirectionProcedure 2 Connecting cables to T1/E1 unit Connecting Power to the Canopy T1/E1 MultiplexerRJ-45 Connector Canopy BH PinProcedure 3 Connecting the AC adapter +3.3 v DC power source Procedure 4 Connecting the −48 v DC power sourceProcedure 5 Installing Software from the CD-ROM Initial Configuration ProceduresInstalling Software from the CD‐ROM Issue the Start-Run-d/setup sequenceUsing EMS Software to Configure the Unit File drop-down menu in GUIProcedure 6 Configuring serial port Accessing the CLI using a PC + HyperTerminalConfiguring the Canopy T1/E1 Multiplexer using the CLI Parameter ValueCreating a Login Account Command Line Interface windowProcedure 7 Changing Administrator password using the CLI Configuration Procedures Using the CLIChanging the Administrator Password Logging into the SystemAction Steps Procedure 8 Selecting line type T1 or E1 using the CLISelect Line Type T1 or E1 Enter get line typeEnter set line 1/2/3/4 code HDB3/B8ZS/AMI Procedure 9 Configuring line coding using the CLISelect Line Coding Enter get line codeAction Configure PortsProcedure 10 Configuring the Ethernet ports using the CLI Enter set canopy port auto negotiation on/offProcedure 11 Configuring the T1 ports using the CLI DB 266-399 / 1.8 dB 399-533 / 2.4 dB 533-655Enter set master clock reference line 1/2/3/4 Enter set clock source loopback/recoveredEnter set secondary clock reference line 1/2/3/4 Procedure 12 Configuring the E1 ports using the CLI Enter set line 1/2/3/4 code HDB3/AMISet clock source recovered Set clock source loopbackConfigure Timing Procedure 13 Configuring timing using the CLIEnd of procedure Configuration Procedures Using the EMSProcedure 14 Logging in using the EMS Login dialogue box T1/E1 Multiplexer EMS main menu End of procedure File→Command Line Terminal from the EMS Main menuChanging the Administrator Password Procedure 17 Configuring T1 line coding using the EMS Procedure 16 Selecting line type T1 or E1 using the EMSSelect Configure Line Type Select Configure T1Select Configure E1 Procedure 18 Configuring E1 line coding using the EMSProcedure 19 Configuring the Ethernet ports using the EMS Click ↓ for Master Clock Reference Line Procedure 21 Configuring the E1 ports using the EMSClick ↓ for Secondary Clock Reference Line Procedure 22 Configuring timing using the EMS Remote Management Through Control Port Remote management overviewProcedure 23 Displaying the alarms using the CLI Enter get alarmsProcedure 24 Displaying alarms using the EMS Select the Alarms→T1/E1 Alarms menuProcedure 25 Resetting the system using the CLI System ResetProcedure 26 Resetting the system using the EMS Canopy T1/E1 Multiplexer in T1/E1 Loopback mode T1/E1 LoopbackProcedure 27 Invoking a T1/E1 loopback using the CLI Invoking a T1/E1 Loopback using the CLIInvoking a T1/E1 Loopback Using the EMS Procedure 28 Invoking a T1/E1 loopback using the EMSComparison of diagnostic measurements Measurements from DiagnosticsFirmware Upgrades Procedure 29 Upgrading firmwareFpga revision details screen End of procedure Click DownloadLicense KEY Upgrades T1/E1 Port Upgrade windowInvalid key entry window Terms of Warranty Software License Terms and ConditionsCanopy T1/E1 Multiplexer Hardware Warranty in U.S Obtaining Technical SupportInvoking Your Warranty Rights Enter get canopy port auto negotiation CLI Commands to GET Status InformationDesired Action Syntax, Response, and Description Enter get lan port auto negotiationEnter get line 1/2/3/4 length Enter get code line 1/2/3/4Enter get master clock reference line Enter get clock sourceEnter get secondary clock reference line Enter get loopback line 1/2/3/4 Enter get firmware revisionRegulatory Compliance Information European Telecommunications Standards Institute TRADEMARKS, Product NAMES, and Service NamesDepartment of Communications Canada Canadian Compliance StatementReferences