Motorola T1/E1 manual Front Panel, Status Leds, LED status indicator descriptions

Page 14

Canopy T1/E1 Multiplexer	September 2004
	T1/E1 Multiplexer FPGA Version 3.4

1.2.5Front Panel

The control port and indicator LEDs are located on the front panel of the unit.

Figure 6: Canopy T1/E1 Multiplexer front panel

Status LEDS

The status indicator LEDS on the front of the Canopy T1/E1 Multiplexer are listed in Table 3.

	Table 3: LED status indicator descriptions

LED	LED indicator descriptions

PWR	ON when main power supply is OK; OFF when a malfunction is
	detected
RDY	ON when self-test is successfully completed; OFF during self-test; and
	BLINKING when self-test fails

CANOPY LINK	OFF when line is not active; ON when Canopy BH Ethernet line is OK

CANOPY ACT	OFF when no activity; BLINKNG when frames are being transmitted or
	received on the line

LAN LINK	OFF when line is not active; ON when line is OK

Issue 3

Page 14 of 73

Image 14

Contents T1E1Mux-UG-en Issue September Canopy T1/E1 Multiplexer User GuideTable of Contents Managing Your Canopy T1/E1 Multiplexers List of Figures List of Tables List of Procedures Using the Latest Information Using this User GuideNew in This Issue Searching This User GuideConstant width bold Font Type of InformationVariable width bold Admonition General Message LabelSending Feedback Introduction to Canopy T1/E1 MultiplexerGetting Additional Help Ethernet Interface Canopy T1/E1 Multiplexer with Canopy BHsRear Panel StandardsIDU Physical Description Rear panel with standard 110-v source power supply Canopy T1/E1 Multiplexer Front Panel LED status indicator descriptionsLED indicator descriptions Status LedsPhysical Specifications FeaturesSpecifications Canopy T1/E1 Multiplexer physical specificationsT1 framing specifications Technical SpecificationsT1 port specifications E1 port specificationsLocal terminal and control interface specifications Configuration Settings from Canopy FactoryE1 framing specifications Bit Handling CapabilityFunctional Description of the Canopy T1/E1 Multiplexer Power AdaptersProduct Labels License KeysChannel Modes T1 Channel ModeE1 Channel Mode EncodingBinary Eight Zero Substitution Coding Alternate Mark Inversion AMI1 in 15 Requirement AMI High Density Bipolar Order Three Encoding SignalingTiming Frequency off-set by clock type Master and Secondary ClocksRecovered Timing Mode Loss of Clock SignalLoopback Timing Mode Timing ModesSlave timing set to Recovered mode Network Timing ScenariosEthernet Throughput Vlan Support Round‐Trip Packet DelayAlarms Compliance Safety InformationPower Supply Unit Lightning ProtectionPreparing for Installation and Setup Installation ProceduresPackage Contents Mounting the Canopy T1/E1 MultiplexerT1/E1 port connector pin-out Connecting the Canopy T1/E1 MultiplexerEnd of procedure Pin Designation DirectionProcedure 2 Connecting cables to T1/E1 unit Connecting Power to the Canopy T1/E1 MultiplexerRJ-45 Connector Canopy BH PinProcedure 3 Connecting the AC adapter +3.3 v DC power source Procedure 4 Connecting the −48 v DC power sourceProcedure 5 Installing Software from the CD-ROM Initial Configuration ProceduresInstalling Software from the CD‐ROM Issue the Start-Run-d/setup sequenceUsing EMS Software to Configure the Unit File drop-down menu in GUIProcedure 6 Configuring serial port Accessing the CLI using a PC + HyperTerminalConfiguring the Canopy T1/E1 Multiplexer using the CLI Parameter ValueCreating a Login Account Command Line Interface windowProcedure 7 Changing Administrator password using the CLI Configuration Procedures Using the CLIChanging the Administrator Password Logging into the SystemAction Steps Procedure 8 Selecting line type T1 or E1 using the CLISelect Line Type T1 or E1 Enter get line typeEnter set line 1/2/3/4 code HDB3/B8ZS/AMI Procedure 9 Configuring line coding using the CLISelect Line Coding Enter get line codeAction Configure PortsProcedure 10 Configuring the Ethernet ports using the CLI Enter set canopy port auto negotiation on/offProcedure 11 Configuring the T1 ports using the CLI DB 266-399 / 1.8 dB 399-533 / 2.4 dB 533-655Enter set secondary clock reference line 1/2/3/4 Enter set clock source loopback/recoveredEnter set master clock reference line 1/2/3/4 Procedure 12 Configuring the E1 ports using the CLI Enter set line 1/2/3/4 code HDB3/AMISet clock source recovered Set clock source loopbackConfigure Timing Procedure 13 Configuring timing using the CLIProcedure 14 Logging in using the EMS Configuration Procedures Using the EMSEnd of procedure Login dialogue box T1/E1 Multiplexer EMS main menu End of procedure File→Command Line Terminal from the EMS Main menuChanging the Administrator Password Procedure 17 Configuring T1 line coding using the EMS Procedure 16 Selecting line type T1 or E1 using the EMSSelect Configure Line Type Select Configure T1Procedure 19 Configuring the Ethernet ports using the EMS Procedure 18 Configuring E1 line coding using the EMSSelect Configure E1 Click ↓ for Secondary Clock Reference Line Procedure 21 Configuring the E1 ports using the EMSClick ↓ for Master Clock Reference Line Procedure 22 Configuring timing using the EMS Remote Management Through Control Port Remote management overviewProcedure 23 Displaying the alarms using the CLI Enter get alarmsProcedure 24 Displaying alarms using the EMS Select the Alarms→T1/E1 Alarms menuProcedure 26 Resetting the system using the EMS System ResetProcedure 25 Resetting the system using the CLI Canopy T1/E1 Multiplexer in T1/E1 Loopback mode T1/E1 LoopbackProcedure 27 Invoking a T1/E1 loopback using the CLI Invoking a T1/E1 Loopback using the CLIInvoking a T1/E1 Loopback Using the EMS Procedure 28 Invoking a T1/E1 loopback using the EMSComparison of diagnostic measurements Measurements from DiagnosticsFirmware Upgrades Procedure 29 Upgrading firmwareFpga revision details screen End of procedure Click DownloadLicense KEY Upgrades T1/E1 Port Upgrade windowInvalid key entry window Terms of Warranty Software License Terms and ConditionsCanopy T1/E1 Multiplexer Hardware Warranty in U.S Obtaining Technical SupportInvoking Your Warranty Rights Enter get canopy port auto negotiation CLI Commands to GET Status InformationDesired Action Syntax, Response, and Description Enter get lan port auto negotiationEnter get line 1/2/3/4 length Enter get code line 1/2/3/4Enter get secondary clock reference line Enter get clock sourceEnter get master clock reference line Enter get loopback line 1/2/3/4 Enter get firmware revisionRegulatory Compliance Information European Telecommunications Standards Institute TRADEMARKS, Product NAMES, and Service NamesDepartment of Communications Canada Canadian Compliance StatementReferences