Allied Telesis AT-PWR06, AT-DC2552XS, AT-FAN06 manual Powering On the Switch

Page 66

Chapter 5: Powering the Switch

Powering On the Switch

The power turns on automatically when you connect the power cable to one or both of the AT-PWR06 power supply modules. To power on the switch, perform the following procedure:

Note

Power cord is used as a disconnection device. To de-energize equipment, disconnect the power cord. E3

Warning

Pluggable Equipment. The socket outlet shall be installed near the equipment and shall be easily accessible. E5

Note

If one of the power supply slots is empty with the power supply unit not installed, install the cover panel before powering the switch on. Refer to “Installing and Replacing AT-PWR06 Power Supply Module” on page 48

1.Inspect the front of the AT-DC2552XS chassis to insure that at least one AT-PWR06 power supply module and two AT-FAN06 fan modules are installed. If one of these modules needs to be installed, perform the steps described in “Installing Power Supply Module” on page 48 or “Installing Fan Module” on page 52.

2.Connect the AC power cable to the AC power connector on the AT-PWR06 power supply module.

3.Connect the AC power plug to an AC power outlet.

4.With the AC power cable connected to the power supply module and an AC power source, the AC power is turned on to the switch.

You can observe that the AT-PWR06 power (AC OK) LED is solid green. If only one power supply module is powered on, the POWER / FAULT LED on the back of the chassis is blinking yellow.

If two AT-PWR06 power supply modules are powered on, both power supply module AC OK LEDs are solid green and the POWER / FAULT LED is solid green too.

5.If you have installed a second redundant power supply module and have not powered it on, repeat steps 1 - 3.

66

Image 66
Contents Installation Guide Page Electrical Safety and Emissions Standards TickTranslated Safety Statements Contents Page Figures Figures Tables Tables Preface Document Conventions Contacting Allied Telesis Preface Overview ChapterAT-DC2552XS Features FunctionsInstallation Options Optional QSFP+ Transceivers  AT-QSFPSR 40GBASE-SR4 MPOLED LED FANAT-DC2552XS Rear Panel Stack Installation Guide for AT-2552XS L2 Data Center Switch Cable Type 10Mbps 100Mbps 1000Mbps LEDs LEDQSFP+ LEDs QSFP+ LED is described in Table Power FaultLink ACT LED LinkFAN1 FAN2AC OK Console Port AT-PWR06 Power Supply Module Stack Installation Guide for AT-2552XS L2 Data Center Switch AT-FAN06 Fan Module Beginning the Installation Installation Overview Step ProcedureReviewing Safety Precautions Beginning the Installation Stack Installation Guide for AT-2552XS L2 Data Center Switch Beginning the Installation Planning the Installation Unpacking the Switch AT-DC2552XS SwitchAT-PWR06 Power Supply AT-FAN06 Fan Module Installing the Switch and Modules Installing the Switch on a Desktop Installing the Switch in an Equipment Rack Possible Bracket LocationsInstalling the Switch and Modules Mounting the Switch in an Equipment Rack Installing and Replacing AT-PWR06 Power Supply Module Installing Power Supply ModuleInsert AT-PWR06 Module Into Chassis Replacing Power Supply Module Tighten AT-PWR06 Captive ScrewsInstalling Power Supply Blank Cover Installing and Replacing AT-FAN06 Fan Module Installing Fan ModuleStack Installation Guide for AT-2552XS L2 Data Center Switch Replacing Fan Module Installing the SFP+ and QSFP+ Transceivers and Cables AT-SP10SR Installing SFP+ Transceivers and Cables10GBASE-SR 10GBASE-LRInstalling SFP+ Transceiver Removing SFP+ Dust Cover Installing a SFP+ Direct Attach Cables Installing the SFP+ and QSFP+ Transceivers and Cables Installing QSFP+ Transceivers and Cables 40GBASE-SR4AT-QSFPSR Installing the SFP+ and QSFP+ Transceivers and Cables QSFP+ Mthtp Installing the SFP+ and QSFP+ Transceivers and Cables Powering the Switch Powering On the Switch Stack Installation Guide for AT-2552XS L2 Data Center Switch Turn Off the switch Managing the Switch Connecting the Console Port Local ManagementStack Installation Guide for AT-2552XS L2 Data Center Switch NET Mgmt Cable Installation Remote Network ManagementStack Installation Guide for AT-2552XS L2 Data Center Switch Managing the Switch Troubleshooting Troubleshooting Stack Installation Guide for AT-2552XS L2 Data Center Switch Troubleshooting Environmental Specifications Technical SpecificationsPhysical Specifications Appendix aQuality and Reliability Power SpecificationsCertifications MtbfRJ-45 Twisted Pair Port Pinouts TX+ RX+Pinout Pair Stack Installation Guide for AT-2552XS L2 Data Center Switch Appendix a Technical Specifications