Omnitron Systems Technology RS-232 user manual Example

Page 10

5.Press the <Enter> key. The reader will beep twice to indicate the reader is now in the Setup Mode for group X.

6.Type the two-character selection code for the feature that you wish to change.

7.Press the <Enter> key. The reader will beep twice to indicate the code is accepted by the reader as a valid code for Setup Group X.

8.Type the one-character code for the change you wish to make.

9.Press the <Enter> key. The reader will beep twice to indicate the code is accepted by the reader as a valid code for that particular feature.

10.Repeat Steps 6 to 9 for any other features that you wish to change in the same Setup Group.

11.Save the changes and exit Setup Mode by typing XZ. (Of course, X must be the same group name entered in Step 4.)

12.Press the <Enter> key. The reader will sound four beeps to indicate

the new settings have been saved in the reader and the reader is back to the normal reading mode.

EXAMPLE:

To set the reader’s beep volume to LOW, enter following setup code in Notepad:

/E/D/FB<Enter>B1<Enter>1<Enter>BZ<Enter>

The setup routine is always the same, regardless of group:

1.Enter group setup mode.

2.Enter the feature selection code.

3.Change the setting for that feature.

4.Save the change and exit.

The reader’s response is always the same, regardless of group:

·Two slow beeps indicate the code has been accepted by the reader.

·Four slow beeps indicate the reader has saved the settings and has exited the setup mode successfully.

·Four quick beeps indicate the code entered is invalid and has been rejected by the reader.

Before proceeding to enter the next code, make sure the reader gives the correct number of beeps when <ENTER> is depressed.

4

Image 10
Contents Omnitm Page Limited Warranty Agency ApprovedPage Table of Contents Page Introduction SectionDescription Installation Host ConnectionsBar Code Input ConfigurationConfiguration Setup Procedure Magnetic Stripe InputExample Default Settings Serial Interface Parameters Group EBaud Rate ParityGeneral Selections Group B Stop BitCode/Track ID Beep VolumeScan Verification Code ID Definition Group Enter one character for the new IDBar Code Message Formatting Selections Group C Bar Code Terminator CharacterBar Code Preamble Bar Code PostambleMagnetic Stripe Formatting Selections Group D Magnetic Stripe Terminator CharacterMagnetic Stripe Preamble Magnetic Stripe PostambleIndustrial Bar Codes Group F Bar Code SelectionsMinimum and Maximum Length Options Enable/Disable Code Code 39 SettingsFull Ascii Check Digit Interleaved 2 of 5 SettingsEnable/Disable Interleaved 2 Send Start/Stop CharactersFebraban Conversion Fixed LengthIndustrial 2 of 5 Settings Enable/Disable Industrial 2Code 128 Setting Codabar Settings Enable/Disable CodabarEnable/Disable MSI/Plessey MSI/Plessey SettingsTelepen Setting Enable/Disable TelepenEnable/Disable UPC-A UPC SettingsRetail Bar Codes Group G Send Check Digit Enable/Disable UPC-ESend Number System Digit UPC-E ExpansionAddendum Required Read Two-Digit AddendumRead Five-Digit Addendum Add Separator SpaceEnable/Disable EAN-8 EAN SettingsEnable/Disable EAN-13 Send Induced Country Code CharacterRead Five-Digit Addendum Do Not Read Five-Digit Addendum Track Selection Magnetic Stripe Selections Group HSend Start/Stop Sentinel Track Separator Reviewing Configuration SettingsTrack Two Send Accout Number Only H4ENTERSELECTED CharacterenterMSI Data Editing Data Fields Data Editing Formulas Formula Sequence Code IdlengthmatchdivideaddsendUsing the Data Editing Functions Track 1 %CABREADOE$JANE$R$310 S Jefferson ST?Data Editing On/Off Data Editing CommandsUnmatched Input Send/Do Not Send Set Length Select Code IDsJDENTER0ENTER6ENTER1ENTER2ENTER JEENTER0ENTER8ENTERAENTERBENTER Centerdentereenter Match StringCreate a Data Field JFENTER0ENTER7ENTERAdd a Data Field Search for a Data StringJgenteraenterbentercenter Dentereenter Delete One Formula Time DelaySet the Sequence in which Data Fields are Sent JkenteraentercenterbenterExit Data Editing Mode Reset Data Editing GroupReview Configurations Omni Data FlowSymbology Code ExamplesEnter 7ENTER Send BD DLY 09 AD DLYJDENTER0ENTER7ENTER0 JEENTER0ENTER7ENTERMSR Track 1 data Operating Procedure OperationTroubleshooting General ProceduresSerial Interface Problems Scanning Configurations Appendix a Default SettingsCrlf Industrial Bar Codes UPC-A, -E Retail BarcodesUPC-A UPC-E EAN-8 Appendix B Magnetic Stripe FormatAppendix C Magnetic Stripe Standard Data FormatsCalifornia Driver’s License Format Track LRE ID Aamva Driver’s License Format Track Appendix D Full Ascii TableAscii Appendix E Connector PIN-OUTSRS-232 Port, Standard DB-9P Appendix F Installing the DriversUSB/RS-232 Interface Page UE Anyway Telling Whether the Installed Device is Type a or Type B Checking the Installation and Modifying the COM Port NumberTroubleshooting Updating the Driver Date DriverRemoving the Driver Versal Serial BUS ControllersID Tech