Omnitron Systems Technology RS-232 Select Code IDs, Set Length, JDENTER0ENTER6ENTER1ENTER2ENTER

Page 42

Select Code ID(s)

This command designates the bar code symbologies or magnetic stripe tracks that will be accepted as valid.

SELECTION CODE: JC

 

UPC-A

a

UPC-E

b

EAN-8

c

EAN-13

d

Code 39

e

Interleaved 2 of 5

f

Industrial 2 of 5

g

Code 128

h

MSI/Plessey

i

Codabar

j

MSR Track 1

k

MSR Track 2

l

MSR Track 3

m

Telepen

n

EXAMPLE:

To designate UPC-A, Code 39, Codabar, and MSR Track 1 as the only valid sources of data, enter:

... JC<ENTER>a<ENTER>e<ENTER>j<ENTER>k<ENTER> ...

Set Length

Use this command to indicate a minimum and maximum number of characters allowed for valid data. The first two digits set the minimum length, and the second two digits set the maximum length. (This command is optional.)

SELECTION CODE: JD

Two Digits for Minimum Length

Two Digits for Maximum Length

EXAMPLE:

To set the minimum number of characters at six, and the maximum at twelve, enter:

... JD<ENTER>0<ENTER>6<ENTER>1<ENTER>2<ENTER> ...

36

Image 42
Contents Omnitm Page Limited Warranty Agency ApprovedPage Table of Contents Page Section IntroductionDescription Installation Host ConnectionsBar Code Input ConfigurationConfiguration Setup Procedure Magnetic Stripe InputExample Default Settings Serial Interface Parameters Group EBaud Rate ParityGeneral Selections Group B Stop BitBeep Volume Code/Track IDScan Verification Code ID Definition Group Enter one character for the new IDBar Code Message Formatting Selections Group C Bar Code Terminator CharacterBar Code Preamble Bar Code PostambleMagnetic Stripe Formatting Selections Group D Magnetic Stripe Terminator CharacterMagnetic Stripe Preamble Magnetic Stripe PostambleBar Code Selections Industrial Bar Codes Group FMinimum and Maximum Length Options Code 39 Settings Enable/Disable CodeFull Ascii Check Digit Interleaved 2 of 5 SettingsEnable/Disable Interleaved 2 Send Start/Stop CharactersFebraban Conversion Fixed LengthIndustrial 2 of 5 Settings Enable/Disable Industrial 2Code 128 Setting Codabar Settings Enable/Disable CodabarEnable/Disable MSI/Plessey MSI/Plessey SettingsTelepen Setting Enable/Disable TelepenUPC Settings Enable/Disable UPC-ARetail Bar Codes Group G Send Check Digit Enable/Disable UPC-ESend Number System Digit UPC-E ExpansionAddendum Required Read Two-Digit AddendumRead Five-Digit Addendum Add Separator SpaceEnable/Disable EAN-8 EAN SettingsEnable/Disable EAN-13 Send Induced Country Code CharacterRead Five-Digit Addendum Do Not Read Five-Digit Addendum Magnetic Stripe Selections Group H Track SelectionSend Start/Stop Sentinel Track Separator Reviewing Configuration SettingsTrack Two Send Accout Number Only H4ENTERSELECTED CharacterenterMSI Data Editing Data Fields Data Editing Formulas Formula Sequence Code IdlengthmatchdivideaddsendUsing the Data Editing Functions Track 1 %CABREADOE$JANE$R$310 S Jefferson ST?Data Editing Commands Data Editing On/OffUnmatched Input Send/Do Not Send Select Code IDs Set LengthJDENTER0ENTER6ENTER1ENTER2ENTER JEENTER0ENTER8ENTERAENTERBENTER Centerdentereenter Match StringCreate a Data Field JFENTER0ENTER7ENTERSearch for a Data String Add a Data FieldJgenteraenterbentercenter Dentereenter Delete One Formula Time DelaySet the Sequence in which Data Fields are Sent JkenteraentercenterbenterExit Data Editing Mode Reset Data Editing GroupReview Configurations Omni Data FlowSymbology Code ExamplesEnter 7ENTER Send BD DLY 09 AD DLYJDENTER0ENTER7ENTER0 JEENTER0ENTER7ENTERMSR Track 1 data Operating Procedure OperationTroubleshooting General ProceduresSerial Interface Problems Scanning Configurations Default Settings Appendix aCrlf Industrial Bar Codes Retail Barcodes UPC-A, -EUPC-A UPC-E EAN-8 Appendix B Magnetic Stripe FormatAppendix C Magnetic Stripe Standard Data FormatsCalifornia Driver’s License Format Track LRE ID Aamva Driver’s License Format Track Appendix D Full Ascii TableAscii Connector PIN-OUTS Appendix ERS-232 Port, Standard DB-9P Installing the Drivers Appendix FUSB/RS-232 Interface Page UE Anyway Checking the Installation and Modifying the COM Port Number Telling Whether the Installed Device is Type a or Type BTroubleshooting Updating the Driver Date DriverRemoving the Driver Versal Serial BUS ControllersID Tech