Omnitron Systems Technology RS-232 Code ID Definition Group, Enter one character for the new ID

Page 15

Code ID Definition (Group I)

If the Code ID option is enabled in General Setup, the user can select the character used to identify each symbology.

1.Enter CODE ID DEFINITION SETTINGS MODE by typing /E/D/FI.

2.Press <ENTER>. The reader should beep twice.

3.Enter the characters in the left column to select the symbology.

4.Press <ENTER>. The reader should beep twice.

5.Enter one character for the new ID.

a

UPC-A

Default = a

b

UPC-E

Default = b

c

EAN-8

Default = c

d

EAN-13

Default = d

e

Code 39

Default = e

f

Interleaved 2 of 5

Default = f

g

Industrial 2 of 5

Default = g

h

Code 128

Default = h

i

MSI/Plessey

Default = i

j

Codabar

Default = j

k

MSR Track 1

Default = k

l

MSR Track 2

Default = l

m

MSR Track 3

Default = m

n

Telepen

Default = n

6.Press <ENTER>. The reader should beep twice.

7.Save the change and exit the group setup mode by entering IZ<ENTER>. The reader should beep four times.

Note: To review the group’s current setting(s), type IY<ENTER> while in the Group Setup Mode. To reset the current setting(s) to its group default, type IX<ENTER> while in the Group Setup Mode.

EXAMPLE:

To change Code ID for Code 128 from h to w, enter: /E/D/FI<ENTER>h<ENTER>w<ENTER>IZ<ENTER>

9

Image 15
Contents Omnitm Page Agency Approved Limited WarrantyPage Table of Contents Page Section IntroductionDescription Host Connections InstallationMagnetic Stripe Input ConfigurationConfiguration Setup Procedure Bar Code InputExample Serial Interface Parameters Group E Default SettingsParity Baud RateStop Bit General Selections Group BBeep Volume Code/Track IDScan Verification Enter one character for the new ID Code ID Definition GroupBar Code Terminator Character Bar Code Message Formatting Selections Group CBar Code Postamble Bar Code PreambleMagnetic Stripe Terminator Character Magnetic Stripe Formatting Selections Group DMagnetic Stripe Postamble Magnetic Stripe PreambleBar Code Selections Industrial Bar Codes Group FMinimum and Maximum Length Options Code 39 Settings Enable/Disable CodeFull Ascii Send Start/Stop Characters Interleaved 2 of 5 SettingsEnable/Disable Interleaved 2 Check DigitFixed Length Febraban ConversionEnable/Disable Industrial 2 Industrial 2 of 5 SettingsCode 128 Setting Enable/Disable Codabar Codabar SettingsEnable/Disable Telepen MSI/Plessey SettingsTelepen Setting Enable/Disable MSI/PlesseyUPC Settings Enable/Disable UPC-ARetail Bar Codes Group G UPC-E Expansion Enable/Disable UPC-ESend Number System Digit Send Check DigitAdd Separator Space Read Two-Digit AddendumRead Five-Digit Addendum Addendum RequiredSend Induced Country Code Character EAN SettingsEnable/Disable EAN-13 Enable/Disable EAN-8Read Five-Digit Addendum Do Not Read Five-Digit Addendum Magnetic Stripe Selections Group H Track SelectionSend Start/Stop Sentinel H4ENTERSELECTED Characterenter Reviewing Configuration SettingsTrack Two Send Accout Number Only Track SeparatorMSI Data Editing Data Fields Data Editing Formulas Code Idlengthmatchdivideaddsend Formula SequenceTrack 1 %CABREADOE$JANE$R$310 S Jefferson ST? Using the Data Editing FunctionsData Editing Commands Data Editing On/OffUnmatched Input Send/Do Not Send Select Code IDs Set LengthJDENTER0ENTER6ENTER1ENTER2ENTER JFENTER0ENTER7ENTER Match StringCreate a Data Field JEENTER0ENTER8ENTERAENTERBENTER CenterdentereenterSearch for a Data String Add a Data FieldJgenteraenterbentercenter Dentereenter Jkenteraentercenterbenter Time DelaySet the Sequence in which Data Fields are Sent Delete One FormulaOmni Data Flow Reset Data Editing GroupReview Configurations Exit Data Editing ModeExamples Symbology CodeJEENTER0ENTER7ENTER Send BD DLY 09 AD DLYJDENTER0ENTER7ENTER0 Enter 7ENTERMSR Track 1 data Operation Operating ProcedureGeneral Procedures TroubleshootingSerial Interface Problems Scanning Configurations Default Settings Appendix aCrlf Industrial Bar Codes Retail Barcodes UPC-A, -EUPC-A UPC-E EAN-8 Magnetic Stripe Format Appendix BMagnetic Stripe Standard Data Formats Appendix CCalifornia Driver’s License Format Track LRE ID Aamva Driver’s License Format Track Full Ascii Table Appendix DAscii Connector PIN-OUTS Appendix ERS-232 Port, Standard DB-9P Installing the Drivers Appendix FUSB/RS-232 Interface Page UE Anyway Checking the Installation and Modifying the COM Port Number Telling Whether the Installed Device is Type a or Type BTroubleshooting Date Driver Updating the DriverVersal Serial BUS Controllers Removing the DriverID Tech